Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RB525GV5

RB525GV5 Hotpoint Range - Overview

Get Parts and Repair Help for RB525GV5

If you know the range repair part you need, you can browse the list of all parts on the RB525GV5, or you can search by name or part description. You can also find your part by where it is located on the RB525GV5 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for RB525GV5 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the RB525GV5

[Viewing 3 of 3]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.37

Surface Burner Terminal Block Kit

Also known as receptacle.

Order within the next 3 hrs and your part ships today!
$36.66

Surface Element - 8" - 2350W

The surface element, also known as the coil surface element, transfers heat to the area on top of range. The element is 8 inches in diameter. If your surface element does not heat, over heats, or heats inconsistently, replacing this part can be the solution to your issue. To determine whether the element is defective, use a multimeter to test it. Before installing the new element, make sure the drip bowl is properly aligned with the notch of the pan. Insert the new element into the reciprocal at a 40 degree angle. Refer to the instructions provided by the manufacturer for more guidance.

Order within the next 3 hrs and your part ships today!
$27.16

Surface Element - 6" - 240V

If you notice that your surface element will not heat properly, you may need to replace it. This surface element is 6 inches in diameter and 240V. It is a Y-frame surface burner el...

Order within the next 3 hrs and your part ships today!
$27.10

Infinite Switch Kit

The infinite switch controls the stove top surface burner. This switch will work with most of the electrical range models with coil burner elements.

Order within the next 3 hrs and your part ships today!
$5.25

Drip Bowl - 6"

This 6 inch chrome drip bowl is intended for use with solid terminal plug-in style surface burner units on electric ranges.

Order within the next 3 hrs and your part ships today!
$48.31

Bake Element

This bake element has push-on wire terminals and the feet to keep it elevated from the bottom of the oven.

Order within the next 3 hrs and your part ships today!
$4.97

Drip Bowl - 8"

This 8 inch chrome drip bowl is intended for use with solid terminal plug-in style surface burner units on electric ranges.

Order within the next 3 hrs and your part ships today!
$18.43

Broiler Pan - Large

This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures 15-1/2 inches wide by 13 inches deep and the pan is about 17 inches wide by 13 inches deep. No tools are required to replace this item, simply pull out the lower drawer of your range, pull down the front of the drawer, slide the pan out and slide the new one into place. This is a genuine part sourced right from the manufacturer.

Order within the next 3 hrs and your part ships today!
$7.36

Foot - Leveller

Sold individually.

Order within the next 3 hrs and your part ships today!
$1.62

Screws - Package of 12

Order within the next 3 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The Bake-o-lite (Hard Plastic) block that holds the burners female connection in place had chipped away over time and wouldn't allow the male part of the burner to connect up correctly.

  • Customer: Robert from Mt. Vernon, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 100 of 102 people found this instruction helpful
After unplugging the range I took the rear sheet metal panel at the top off with a nut driver to expose the wiring connections. The next step was to remove the single screw holding the old part in place. (under the drip pan) Once free I snipped the old part from the wires and then taped the new female ends to the old wires with black electrical tape. From re... read more

Front burner would not heat up

  • Customer: Scott from Olathe, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 68 of 96 people found this instruction helpful
1. Pull out range and unplug from socket.
2. Lift range lid.
3. Remove back panel. Loosen the 6 - 1/4" nuts, then lift up slightly, which compresses the "latch" at the top middle. Let down and panel comes off easily.
(Note: Do not remove wires yet)
4. Remove control knob from front panel by pulling gently, exposing 2 small tap screwsread more

Bottom heat element

  • Customer: Alton from Marshall, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 42 of 43 people found this instruction helpful
Turn the breaker off to the oven.Removed both wire racks,using a 1/4 nut driver unscrewed the old element.The flashlight was so I could see inside the oven.Having removed the two screws ,the old element came right out.With my needle nose pliers removed the wires one at a time,replacing them on the new element as they came off.Replaced the two screws holding ... read more