RB525C2WH Hotpoint Range - Instructions

Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy

removed old gasket and clips, replaced with new gasket that came with clips. easy. worked well.

I pulled range away from the wall and pulled the electrical plug. I removed all of the heating elements and raised and secured the top panel.I then removed the one screw that held the terminal block in place.now I went to the rear of the range and remove six screws that held the top cover in place.I now cut the two wires going to the old block,I pushed the new wires through the back panel.I installed the new terminal block using one screw. Now I went to the rear and removed the old wires and installed the new wires. I rolled up excess wire and secured with plastic ties. I installed the rear cover using six screws,I put electrical plug back into outlet,pushed range back in place,lowered front panel,replaced all the elements and turn on left rear element.FINISH EVERYTHING WORKS. P.S. I ordered two terminal blocks,if it happens again in any of the blockes I'll be ready. total costs for both $25.55 plus shipping.

The new drip pans are great. I had purchased generic ones locally that were supposed to be universal. The problem was that they did not fit right and the burner coils did not sit flat. The new drip pans fit well and look great too.

The drip pans arrived and she switched them out with the old ones Easy!

I ordered new drip bowls and put them in place. They fit just fine.

After searching the internet for a cause for the burner not getting hot it looked as though it was the burner switch. I ordered the switch and installed it. Behold it still did not work. I then ordered the burner, installed it and it worked. So I had a 50/50 chance as to which part was the problem. This was my first stove repair and I found it easy to do. Finding something to hold up the ceramic cooktop took the most time. I cut a piece of wood to prop it up while I replaced the burner.

attached the element,pushed it back in the pocket,put the plate back on, screwed the nut and bolt back on and was done in less than 4 minutes!!

replaced pans- what I would like to comment on is the time- I ordered one day at noon and had them the next day at noon- I live in tiny town on northern border of USA- it was awesome- I couldn't believe it was them- 24 hours- super job and excellent price too

best to pull stove out away from wall connect from behind stove

Pull knob. Pull wires. Pull two screws. Replace switch

Very easy. Followed the video instructions. Unplug stove. Cut old wires. Tape new wires to old wires to facilitate pulling new wires thru old hole to back of range. Removed back cover. Pulled old/new wires thru to back. Removed old connectors. Attached new connectors. Replaced back cover. Screwed new terminal block to front of range at burner. Attached new burner. Plugged in stove. Replaced stove in counter.

Unplug heating elements and pick up drip bowels and reinstall elements.

Turn off power to oven. Removed the rack. used a 1/4" nut driver and removed the two screws holding the element to back of oven. Slid the element out, unhook the two wires clipped to the end of the element. Replaced it with the new element, installing it in reverse. Took about 15 min. Rememer to turn off power to oven before attempting to work on it.

Removed old socket, I had replaced with a aftermarket that really did not work well. When I recieved the terminal block kit from your company it was the proper kit. Service was better than expected, part and price was great and it took very little time ti install. Thank you.