Models > RB525*J2 > Instructions

RB525*J2 Hotpoint Range - Instructions

All installation instructions for RB525*J2 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RB525*J2
1-15 of 420
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

element quit working

  • Customer: Wilbur from Taylorville IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 464 of 464 people found this instruction helpful
Unhooked electrical wiring from unit and rehooked new unit to electrical wiring.

Bottom heating element went out

  • Customer: Michael from Saint Paris OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 369 of 373 people found this instruction helpful
This repair took between 15 and 30 minutes BUT ONLY because my 10 year old son did the repair. He couldn't wait for his father to come home from work. His only complaint was the tight fit to reach the back of the oven (he wanted to take the oven door off but I said no). He removed the 2 screws that held the element in place and then pulled it from the oven until he could remove the screws that held the wires in place. He was concerned that a little of the insulation came out with the wires, but this was no issue. The new element hooked right up (we figured out that we had to use the 2 new screws for the wires because the old ones did not fit very well). We used the same 'old' screws to attach the element back to the oven. Plugged the oven back in and it works fine. My son was so proud and I didn't have to help any more than shining a flashlight for him.

Oven heating element was broken.

  • Customer: Phyllis from Fisk MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 256 of 329 people found this instruction helpful
The heating element in the lower oven of my 18 year-old GE double oven broke into two pieces and would not heat. Because of the age of the oven, a replacement part was unavailable through GE. I came across PartSelect.com through an Internet search and ordered the part online. Total cost was $33.50, counting s/h. FedEx delivered the new element less than 48 hours after I placed the order online.

IMPORTANT: FLIP the BREAKER to stop electricity from going to the oven. Replacing the heating element is a two step process: 1. Remove the old element. 2. Install the new element in its place. (NOTE: This job is much simpler if you lift and remove the oven door BEFORE you begin. NOTE also: There are no slots in the screws, so you must use a small socket wrench--not a screwdriver-- to remove the screws.) STEP 1: Two screws go through the small metal plate attached to the element prongs. These screws hold the element to the back oven wall. Remove the screws, then pull the element forward a few inches to gain access to two screws which hold the element prongs to wires that come through the back oven wall. (One wire and one screw for each of the two prongs.) Remove the two screws. Remove and discard the old element. STEP 2: Install the new element by doing Step 1 in reverse. Oven is now repaired! (It took more time to type these instruction than it took to repair the oven.)

The oven element had broken in half and was sparking

  • Customer: Brittany from Cayce SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 113 of 176 people found this instruction helpful
I am not a handy person so I was really nervous about doing this. I first unplugged the oven just to be on the safe side. Then I removed the two screws that hold the element in place. Next I pulled the element forward and disconnected the two wires. After that I simply reconnected the two wires to the new element, pushed it back in and put the screws in. Piece of cake!

oven would no longer heat. Only broiler worked

  • Customer: Liz from Williamson NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 90 of 152 people found this instruction helpful
First I removed the 2 screws that held the bake element in place. Then I pulled the element out and disconnected the two wires. Reconnected the two wires to the new element and pushed it back in place and installed the unit again with the 2 screws. Turned the oven on and it heated up like it should.

bake element bent down to bottom of oven (ready to break)

  • Customer: James from Tazewell VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 24 of 29 people found this instruction helpful
1) turned off breaker to oven
2) removed oven racks
3) removed screws holding old element
4) pulled out element far enough to remove 2 wires attached to old element
5) noted colors, left white, right black
6) attached new element to wires
7) attached new element to oven
8) put back oven racks
9) turn breaker back on
10) test oven
done

The bottom element had broken apart and needed to be replaced

  • Customer: Becky from Norman OK
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 18 of 20 people found this instruction helpful
The only reason I mentioned "a bit difficult" is that it is very important to unplug the unit first. I didn't want to say easy because I didn't want someone just jumping right in, (you do end up handling raw wires).
First I removed the two screws that were holding in the element to the back wall of the oven, then pulled out the old element slightly until you see where the wires are attached to the end of the element. I made note (I don't know if this is neccessary) which wire came off which screwset so I could put the new one in the same way. Took out the old element and attached the new one to the two screwsets on the ends of the element and then reinserted that part in in the back wall of the oven and attached plate that holds it in place. It was for my mother and she now thinks I'm a genius! Don't let anyone take a picture of you of you from behind because you definitely have to put your head in the oven. I believe the door is removable that may make it easier to get to it.

Two 6" and two 8" burner elements needed replacing on a 36 year old counter range.

  • Customer: Charles from McAllen TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 19 of 24 people found this instruction helpful
First of all I want to thank PartSelect. I have been looking for these parts for over 15 years. I am so happy to have found PartSelect. 1. Turn off Range 2. Turn off Breaker to the Range at your home Breaker Box. 3. Turn on Range to see if you turned off the right Breaker if so then turn Range off. 4. Lift Burner Element up. 5. Take off Silver Trim Ring and Drip Bowl. 6. With screw driver unscrew the screw that is holding the Burner Element to the Range. It is located at the base of the hing where the Burner Element attaches to the Range. 7. Pull the Burner Element out just far enough to see the entire Element where the wires attach. 8. Snap off the two silver clips from each side of the White Glass Insulation Block with a screw driver. 9. With an adjustable wrench (crescent) loosen and remove the screws holding one of the wires to the Burner Element. 10. Find the same Terminal on the new Burner Element and reattach the wire to the new Burner Element Terminal. 11. Now do the same to the remaining Terminal. 12. Install the White Glass Insulation Block over the two Terminals and secure with the two silver clips. 13. Reattach Burner Element to Range with screw. 14. Replace Silver Trim Ring and Drip Bowl. 15. Turn on Breaker and test by turning on Range. You will smell a slight electrical burn smell for a moment while the new Elements heat for the first time. This will dissipate quickly. NOTE: I used the old White Glass Insulation Block I did not use the one that came with the new Burner Element. I found the old one to be the better choice. I saved the new one in case needed at a later date. The Job to replace both the 6" & 8" Burner Elements took less than 30 Minutes. I think it took longer to write this replacement instruction. LOL Very easy...Thanks again PartSelect. Charles McAllen, Texas

Needed to replace Drip Pans and Trim Rings for old stove

  • Customer: Cynthia from Tampa FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 17 of 20 people found this instruction helpful
Repair was simple (just lift off the old and put on the new). What was pleasantly surprising was how quickly I received the parts (amazing)!

Lastly, I've been looking for the correct parts/sizes in stores for years (yes, I should have tried this sooner). I was delighted to finally find a place that actually had the correct parts.

Element burned into.

  • Customer: Ward from Gilmer TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 15 of 16 people found this instruction helpful
First I removed the two screws that held the element in place. I pulled the element out about 2-3 inches and then removed the two screws that fastened to the ends of the element. Was careful to keep the same wires separate in order to fasten the new element back to the same two wires. When fastening the new element ends back to the wires, care must be taken to not bend the ends of the element when tightening the small screws to the ends. Everything went real good and am most pleased with the very fast service portrayed by Parts Select. They are a class act company and rate very high in customer satisfaction!

The bake element would not heat up.

  • Customer: Douglas from Derry NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 11 of 11 people found this instruction helpful
This repair took much longer than it should have.
When I noticed the oven would not heat in bake mode, I suspected the element was bad. Going on the forum, I found that I needed to ohm out the element to be sure, so from inside the oven, I removed the two screws holding the element into the stove, pulled out the element a bit and removed the screws from each contact, ohmed it out and found no continuity. I ordered a new bake element which arrived in a couple of days.
I installed the new element by connecting the wires back to each terminal end. It still didn't work and not only that, the broil element didn't work now either.
I inquired again on the forum and found that the suspect might be the control module that controls both bake and broil elements. The part was $250.
Not wanting to spend that on a 10 year old stove, I ordered a new stove at Sears that was on sale.
I sent the bake element back and waited for my stove to arrive.
Sears called a few days later that my stove was ready for pickup so in preparation, I pulled my old stove out from the wall and began to disconnect the pigtail to use on the new one. It was then I noticed a wire dangling that seemed to go to one side of the bake element. When I pulled out the bake element initially and disconnected the wires, I didn't notice that one terminal had TWO wires going to it and one had a single wire connected. It was a bit dark inside the stove when I initially took the screw off of each terminal and I never noticed the second wire on the left one. I installed the old bake element, knowing it may not work but just to see if the broil now worked and it did!
So I ordered another bake element and installed it connecting two wires to the left terminal and one to the right terminal, reattached it to the back of the oven and IT WORKS!!

I cancelled my new stove at Sears which saved me about $500. Just a $26.00 part.

Bake Element burnt up

  • Customer: John from Lafayette LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 11 of 11 people found this instruction helpful
Turned off breaker to stove.Used nut driver to remove the holding plate from the back ove the oven. Their was between 4 to 6 inch of slack on the wire. Used the nut driver and removed the red wire from the right side of the old element, and then removed the white wire from the left side of the element. Replaced the cap head screws that required a nut driver, with the slotted screws that came with the new element, replaced the white wire(left) the red wire(right), end reattached the holding plate to the back of the oven and done!
There are stand offs on the bottom of the element, so you can't get it confused on where the wires go, but take care that the wires do not slip back in the element "hole" or you will have to "fish" them back out.

Brought the element up slowly to 500 degrees, to burn off any residue on the element. Smelled a chemical smell for the first 5-10 seconds of the "burn in", then no smell.

2' crack in the baking element near the plug

  • Customer: Shalgit from North Potomac MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 9 people found this instruction helpful
I have a 22 year old GE double oven with a range top that I can't live without. I do alot of cooking, baking, and my share of entertaining. To replace this oven I would have to sacrifice having 2 ovens...or remodel my kitchen and reposition their location. So when something goes wrong with this oven I cringe. It needs to keep ticking for another 10 years. A friend recommended PartSelect. looked on line and found the part resembling mine. I called just to confirm the part was correct, and found out it was not. I looked up the part number the said was correct but the shape was wrong. I order it anyhow and when it arrived it was what I needed. The picture on the website was inconsistant with the part number. So I'm really glad I called and spoke to a rep. The part arrived in 4 days and the next day I installed it, needing only one tool. Doing it myself saved me a few hundred dollars and my oven works great again. And their price was lower than a local parts dealer. I added PartSelect to my favorite list for future needs! Thanks!

Large burner would operate on high setting only.

  • Customer: Ernest from Bellevue NE
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 10 of 12 people found this instruction helpful
1. Removed the back panel.
2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time.
3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range.
4. Replaced the burner knob and replaced the back panel.

Broiler Element Burned Out

  • Customer: Richard from Vestal NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 9 of 10 people found this instruction helpful
Successful repair to Our GE range, manufactured prior to 1965 (when installed in house). Pulled range from wall, unplugged, removed burned-out broiler element. Previous check with GE to make cross reference of range part number to Part-select part number for this nearly 50-year-old range. Obtained new part and installed. Works. Range has self-cleaning oven, accidentally destroyed thermal switch attached to element mounting bracket, difficulty with frozen mounting nut. Self-cleaning still works; thermal switch locks out a solenoid which defeats door latch; prevents premature opening of oven door when oven too hot to open safely. Internet search did not find GE part but there are generic devices of the same type available; will consider installation later.
All Instructions for the RB525*J2
1-15 of 420