Models > RB18HY-3AW

RB18HY-3AW (8B22A) Magic Chef Refrigerator - Overview

Get Parts and Repair Help for RB18HY-3AW

If you know the refrigerator repair part you need, you can browse the list of all parts on the RB18HY-3AW, or you can search by name or part description. You can also find your part by where it is located on the RB18HY-3AW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for RB18HY-3AW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the RB18HY-3AW [Viewing 3 of 3]

$30.70

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air ...

$2.70

Screw

Sold individually.

$2.70

Screw

This screw is sold individually.

$3.17

Light Bulb - 7W

Sold individually. This bulb is a 7 watt appliance incandescent light bulb.

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$2.70

SCREW

Sold individually.

$2.70

Screw

This is screw is sold individually.

$3.56

Plastic Tubing

1/4" Plastic tubing, 8 1/2 feet long.

$2.66

Inlet Hose Gasket

$3.96

Compression Nut

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 88 of 91 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

noisy fan motor

  • Customer: robert from nashotah WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 17 of 20 people found this instruction helpful
rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, close up, reverse pan... read more

freezer would not keep food frozen

  • Customer: chuck from dudley NC
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 13 of 14 people found this instruction helpful
First you must unplug the refrigerator, then remove the top hinge and freezer door, then you must remove the middle hinge to remove the refrigerator door, after that there are 4 screws located in the refrigerator compartment that must be removed that are holding the plastic control knob trim in place. When you remove these screws and drop the trim piece you ... read more