Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RB151PFW (DG11A)

RB151PFW (DG11A) Magic Chef Refrigerator - Overview

Get Parts and Repair Help for RB151PFW

If you know the refrigerator repair part you need, you can browse the list of all parts on the RB151PFW, or you can search by name or part description. You can also find your part by where it is located on the RB151PFW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for RB151PFW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$97.39

Replacement Ice Maker

NOTE: This replacement ice maker mechanism does NOT come with a cover,shut off arm, a wire harness, or the mounting hardware. Must be ordered separately.

$40.25

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a mounting nut for the blade and a cushion. This part provides forced-air cooling for the condenser coil.

$25.56

BLADE-FAN

The fan blade is used to blow air over the condenser.

$20.78

Icemaker Fill Tube

This fill tube grommet is used to supply water to the icemaker and is partially located in the refrigerator/freezer wall.

$13.75

Crisper Shelf Support Kit

This support is used with the crisper drawer shelf.

$36.89

Start Relay

The start relay briefly boosts the compressor, and then shuts off as soon as the motor gets up to speed.

Sensor Shut-Off Arm

This part signals the icemaker to stop making ice once the bin has reached a desired amount.

$2.80

Screw

Sold Individually.

Icemaker Wire Harness

Ice Maker Cover

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 662 of 698 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 243 of 316 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

My refrigerator stopped cooling and the freezer section stopped freezing

  • Customer: garth from forest lake, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 172 of 190 people found this instruction helpful
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot ... read more