Models > RAX7245BL1

RAX7245BL1 Roper Washer - Overview

Get Parts and Repair Help for RAX7245BL1

If you know the washer repair part you need, you can browse the list of all parts on the RAX7245BL1, or you can search by name or part description. You can also find your part by where it is located on the RAX7245BL1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for RAX7245BL1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.69

Agitator Directional Cogs

These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.

$10.86

Direct Drive Motor Coupling

This coupling kit is used between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added strength.

$16.36

Agitator Repair Kit

The agitator kit is most commonly used if the top part of the agitator is not moving correctly but the bottom is. This kit now includes all pieces shown in photo plus the thrust sp...

$28.99

Direct Drive Water Pump

It is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.

$2.58

Suspension Spring

Sold Individually. Appliance takes 3 of this part.

$26.31

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity washers and black spring for compact washers. As per factory, the green spring (1.24") replaces the black spring (1.46").

$14.14

Water Inlet Valve with Mounting Bracket

This part could have either a blue colored valve body or a green colored valve body. There are two ports for water to enter and this valve is compatible with a half inch ID hose. I...

$4.54

Agitator Bolt

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$3.84

Tub Spring

$2.88

Inner Cap Seal

Also known as an O-Ring.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Upper portion of agitator, no longer pushing clothing down.

  • Customer: Matt from Pawtucket RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 568 of 577 people found this instruction helpful
The instructions came with the repair kit, it was fairly simple and straight foward.

One bolt held the entire agitator unit in the washer, as well as held the upper and lower halves together. Once that nut was removed the two halves seperated and the plastic clutch pieces could easily be replaced wtih the new onces in the repair kit.

Ve... read more

No movement from Basket & agitator

  • Customer: Jeff from Wayne NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 566 of 600 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more

REPLACE WATER PUMP COUPLING

  • Customer: RICHARD from PHILA PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 544 of 559 people found this instruction helpful
REMOVED CASING TIP OVER WASHER DISCONNECTED WATER PUMP. DISCONNECTED MOTOR THEN REPLACE COUPLING THEN REASSEMBLE MOTOR THEN REPLACED WATER PUMP. read more