RAX5133AW0 Roper Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Agitator did not spin
Best to use the video on PartSelect rather than the printed instructions that come with the kit.
Parts Used:
-
Keith from Arvata, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Water inlet was faualty and y'alls new one did the trick. Thanks
Took back of washing machine off and put the part on.Easy
Parts Used:
-
Larry from Harrison, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Water pump was leaking
Remove two screws at the back of the control panel and slide forward to release the hooks, unplug the door switch then swing it over the top toward the back. Remove two fasteners at the top holding the case in place with a screwdriver. Slide case toward front of machine and remove to expose the pump. Remove two clips and two hoses from pump. Installation is the reverse of these steps.
Parts Used:
-
Jim from Elon, NC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Stop Agitating
Leaned the washer back to get at the bottom, removed the water holes, removed the water pump, removed the motor, replaced the direct drive motor coupling. Put it back together and it's all good. No clutch or drive problems. Simple fix.
Parts Used:
-
Glenn from Wheaton, IL
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Was this instruction helpful to you?
Thank you for voting!
agitator was slipping
followed the tutorial from partselect--remove fabric softener dispenser(just pull up) remove bolt from agitator and take it off agitator--remove old parts and replace with new ones--reassemble---done.--- took longer to write this almost. Probably saved me 100 dollars. Almost anyone could do this repair if you can read and watch a video.
Parts Used:
-
Ronald from Hancock, VT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Tub will not spin, agitator does not work. Already replaced the drive coupling
I generally followed the video. Disconnected the water hoses, removed the front, laid the washer on its back. My water pump is rusted onto the motor shaft so I left it in place. I removed the water pipes from the pump then removed the pump/motor/gearbox as one unit. Watch out for more water than you think being released from the pipes and pump!! Everything works well with the new clutch fitted.
Parts Used:
-
Raymond from Chagrin Falls, OH
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Noticed the agitator was not engagine and slipping
Took the softener mechanism off by pulling upward. Pried off the cap to the agitator with a screw driver then removed the center bolt with a nut driver. This did take a little effort since it had never been removed. Pulled the agitator out of the washer and cleaned all the parts of any soap residue accumulated over the years. Took the agitator and stood it on the floor placing both feet on the sides and pulled it apart. there is a ring inside that popped out along with the top part of the agitator and the small cogs fell out. Cleaned the two pieces and replaced the cogs, holding the main part upside down lowered the agitator bottom into place matching the four grooves after snapping the unit together slide the cog cover into place and gently replaced the agitator back into the washer and replaced the bolt tightly. Then snapped the softener attachment back into place. This required a good bit of pressure but snapped right into place. Done job. Saved a lot of money and a simple fix to a problem. Agitator now works just as it should, no slippage at all. Took about 30 min all together. You can go online to find installation directions for any brand washer that has a full size agitator.
Parts Used:
-
Wynona Roberts from Zwolle, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
There was a buzzing sound when washer was turned on and did not work in spin cycle.
First let me say that I received the within 24 hours from when I ordered it online. Disconnected electric and water hoses .Removed screws on the top control panel then flipped it back from washer housing . Removed washer housing to expose main motor. Removed motor clips and screws . Removed motor coupling . Installed new coupling . Put it all back together . Works great!
Parts Used:
-
William A. Thompson from royersford, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Was this instruction helpful to you?
Thank you for voting!
Poor agitation
Thurs. followed video directions, found the dogs to be defective and around 2 pm ordered dogs on line. To my surprise, on Friday around 11 am the dogs arrived. My husband installed them and the agitator is fine. I was so amazed at how quickly the dogs came. The machine was ready to go in less than a day. Thank you for your efficiency.
Parts Used:
-
Mary from Cornwall, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
Teeth worn off the dog legs..
Follow the instuctions with the kit. Washer Machine Model # LSQ9244EQO.
Parts Used:
-
GARY from CORTLAND, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Would not spin out all the water from clothes
Similar to the youtube repair video, followed it mostly. This model has a different plug in set up on top where the wiring is. Just unplugged a different plug in a different location. The other difference is that I did a lot of dusting and vacuuming of inside parts and around motor. Also used some spray on rust converter on some rust spots then coated those areas with spray paint. Also where wire harness hooks to the frame I taped up a longer section of the wire to keep the wires together so they could move around and not be damaged. The actual repair took about a half hour, but took more time taking the washer outside on porch then back into the house. Out side repair is better because a significant amount of water came out of the washer and drain hose when we tilted it on the back to remove motor and transmission. Just follow the youtube video instructions and most people should have little or no problems doing the job.
Parts Used:
-
Michael from Tallahassee, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Washer full of water not draining
First I tried take the back off. Wrong move, wasted 30 mins on that. Then drained water into bucket, moved washer on hand truck to garage for more room to work. Had pump & drive coupling out in 20 mins. Found Partslect & ordered parts in 15 mins. Two days later had everything back working in 20 mins. Very Good Srevice.
Parts Used:
-
James from Port St Lucie, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Agitator didn't spin but everything else worked.
The youtube explanation on how to repair was great, especially the instruction to lift up on the bluish plastic ring (to detach the softener dispenser), and not to tighten the bolt too much when reassembling matters.
Parts Used:
-
Kenneth from Phoenix, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!
top half of the 2-part agitator slipping (not turning) due to stripped teeth on these cogs.
removed the softener dispenser, gently pried off the top with screw driver, loosen nut and lift off the unit holding the cogs. On our (Kenmore, series 90) there was a small retaining ring to hold the cogs in place. Removed retaining ring (no tools), and cogs (one at a time). Replace each old cog with the new one, being careful that it's not upside down or backwards. reassemble. test. rejoice! This $3 part plus $7 S&H - saved a $100 house call from the appliance repair man.. YouTube & PartSelect = super Combo! Thanks!
Parts Used:
-
Alan G. from Groves, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
The dog were no good.
Just like it said on YouTube. I am going to order a set of dog for back up.
Parts Used:
-
Roy from Little Suamico, WI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!