Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RAX4232KQ0 > Instructions

RAX4232KQ0 Roper Washer - Instructions

All installation instructions for RAX4232KQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RAX4232KQ0
1,126-1,140 of 1,179
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer spin speed became very slow

  • Customer: David from Sycamore, OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Found this web site after reading forums on slow spins and I determined it was a clutch problem. Ordered the clutch from "Part Select", watched the 19 minute video (excellent) on changing out a clutch from this website. After 1.5 day delivery, I installed per video. Very pleased, thank you; Dave

water pump quit workding no water would drain

  • Customer: Tim from Whitesburg, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I was very happy the part arrived very fast and just what we needed, and service was super.. We took the old pump off slipped the new one into the slot and hooked the clips back on it and tighted it up and plug the washer back in and filled with water and it drained... We started doing laundry right away, and so far so good... Tired to leave a review but it won't let us into the site, but we would use the same company to order from again, thank you so much...

No cold water

  • Customer: Adam from Castaic, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I did a you tube search for "no cold water in washer" and found a video for what the fix is. Afte disconecting the power and water hoses it was Unbelievable how easy it was. Two screws in the back to open it up which I watch on a you tube video which was from part select. Then two spring clamps to open the inside and expose the water valve.. One screw and a hose clip and the valve was out. Did the reverse and put it back together..

Water pump was leaking

  • Customer: Michael from Spencerport, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The repair video was great. I decided not to remove the outer cover as there is room to get to the pump if the washer is tipped back. The pump was easy to fix with the exception of the root cause of the failure. There was water getting to the pump shaft and over time it rusted and expanded in the pump housing causing it to split and leak. Once the old pump was removed, a file was needed to reshape the drive shaft to allow the new pump to be installed. Not bad on a 16 year old washer!

Spin cycle would not complete or spin fast enough

  • Customer: Evan from Batavia, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Replaced Cltch assembly. Hardest part was figuring out how to drop the motor. The clutch is located of the main shaft above the motor, under the drum. Three bolts hold the motor in from underneath, however there is a bolt at the top of the shaft in the agitator assembly. Note location of the snap ring on the shaft holding the clutch assembly, grooves in shaft. The only other issue that I had is the is a triangular metal peice that is not attached in anyway between the drum and framing. It had moved when I had the motor and had to be reset after I did my first test run of washer. Spins out great now!

Spin cycle not working.

  • Customer: Thomas from Brighton, MI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Almost identical to the instruction video that was sent. Very straight forward. I did not take apart the washer to identify the problem. I was short on time so I took a chance and ordered the highest probability cause of the symptoms indicated by your website. It was dead on; the problem is fixed. Parts were received ahead of schedule. Excellent all around.

Washer was not spinning clothes on 1st spin

  • Customer: Jeff from Westfield, IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After researching possible failure modes and reviewing a video for teardown/access from the control panel and access top down I noticed a lot of 'break dust' on top of the transmission. Shorting out the lid switch and putting my little finger on the drum, it would not spin but the clutch was spinning fine. I ordered a new clutch... Interesting thing when I was taking the clutch out... the gear it was attached to slid right off! After figuring out it was too big to go 'back' into the transmission and reviewing the parts explosion diagram... it BELONGED INSIDE THE TRANSMISSION! So I took the transmission cover off, poured out out the black-ish oil with metal filings in it, put the gear inside, filled it back up with 10W30, put the lid on, added the new clutch while it was apart and finished reassembly. Wow! It spins much better than when it was new. I guess never assume what can happen on an assembly line. Thanks for the great site.

washer not spining

  • Customer: Israel from san antonio, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
took motor of 2 screws instaled motor coupling

water drip into tub

  • Customer: Mark from Fayetteville, AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video once, ordered the part, watched it again when the part arrived, went downstairs and made the repair. The video was exactly correct! Hardest part was getting the washer case back in place, and that just took a few minutes. Excellent video!! I will check back here the next time I have a repair to make!! Thanks so much.

No hot water through inlet valve

  • Customer: Greg from Lincoln, NE
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Taking the washer apart was no problem. I just looked on the Internet for a few tips. When removing the valve there was a little water leakage which could not be prevented. When replacing the valve it was not an exact match so I had to install the included bracket. The hard part was reinstalling the washer frame. You have to get both sides lined up to it on the bottom frame. That part would have been easier with another person. After finishing everything worked fine.

No water comming through the valves

  • Customer: willie from bessemer, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removing the led and disconnected the wires and the unscrewed the valve assembly and removed it and reversed the steps putting it back together.

the couplings were broken

  • Customer: oscar from Hollis, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I took apart the cover of the washing machine, remove the back, and disconnected the hoses , also disconnect the controls,remove the pump and the motor,which are ben hold by two brackets, then proceed to remove the old parts and insert the new ones, the only problem is that they fit too tight and I used a round tool to insert the new ones, after that i put everything together and bingo, the machine is working already.

Motor did not turn drum and made sound

  • Customer: AL from Marlton, NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Your video was very helpful in showing steps for repair so I didn't have to discover how to disassemble. The old Direct Drive Motor Coupling had three broken couplers on one side and a cracked center on the other. New Direct Drive Motor Coupling was a much improved design that should last even longer than original. The couplers metal sleeves and overall thicker part was what original should have been.

Washer would not spin

  • Customer: Laura from Ocala, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I Googled "washer would not spin" and came upon the PartSelect YouTube video on replacing the motor coupling. Since this seemed easy enough (and I'm a 40-year-old Mom), I decided to take the washer apart as the video instructed just to see if I could find anything obviously broken or out of place. Low and behold, the rubber gasket around the coupling was broken and indicated the coupling probably was too. I ordered the part through the direct link on the YouTube video and easily put the new coupling on and VOILA! The only thing I'd recommend differently is that you leave the pump alone. It doesn't need to come off to get to the coupling. After wrestling with trying to remove the pump, I left it in place, but not before unknowingly damaging it. I had some rust build-up in there and it made the fit very tight and cracked the part/sleeve the motor drive plugs into. When the washer was reassembled I found I'd caused a leak. But...no biggie. I decided to replace pump, too. Hey, now I know how to! :) Just received that part yesterday and VOILA! It's amazing what you can accomplish with the internet. Don't be afraid of this task, ladies (and gentlemen).

Water leaking onto floor when in use

  • Customer: Troy from Myrtle Beach, SC
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the video instructions supplied with the email from Partselect, the video was very helpful and made the repair simple and fast
All Instructions for the RAX4232KQ0
1,126-1,140 of 1,179