RAS8245EN0 Roper Washer - Instructions

Take out cap and replace with new cup

Remove two screws at the back of the control panel and slide forward to release the hooks, unplug the door switch then swing it over the top toward the back. Remove two fasteners at the top holding the case in place with a screwdriver. Slide case toward front of machine and remove to expose the pump. Remove two clips and two hoses from pump. Installation is the reverse of these steps.

Leaned the washer back to get at the bottom, removed the water holes, removed the water pump, removed the motor, replaced the direct drive motor coupling. Put it back together and it's all good. No clutch or drive problems. Simple fix.

followed the tutorial from partselect--remove fabric softener dispenser(just pull up) remove bolt from agitator and take it off agitator--remove old parts and replace with new ones--reassemble---done.--- took longer to write this almost. Probably saved me 100 dollars. Almost anyone could do this repair if you can read and watch a video.

I generally followed the video. Disconnected the water hoses, removed the front, laid the washer on its back. My water pump is rusted onto the motor shaft so I left it in place. I removed the water pipes from the pump then removed the pump/motor/gearbox as one unit. Watch out for more water than you think being released from the pipes and pump!! Everything works well with the new clutch fitted.

Took the softener mechanism off by pulling upward. Pried off the cap to the agitator with a screw driver then removed the center bolt with a nut driver. This did take a little effort since it had never been removed. Pulled the agitator out of the washer and cleaned all the parts of any soap residue accumulated over the years. Took the agitator and stood it on the floor placing both feet on the sides and pulled it apart. there is a ring inside that popped out along with the top part of the agitator and the small cogs fell out. Cleaned the two pieces and replaced the cogs, holding the main part upside down lowered the agitator bottom into place matching the four grooves after snapping the unit together slide the cog cover into place and gently replaced the agitator back into the washer and replaced the bolt tightly. Then snapped the softener attachment back into place. This required a good bit of pressure but snapped right into place. Done job. Saved a lot of money and a simple fix to a problem. Agitator now works just as it should, no slippage at all. Took about 30 min all together. You can go online to find installation directions for any brand washer that has a full size agitator.

First let me say that I received the within 24 hours from when I ordered it online. Disconnected electric and water hoses .Removed screws on the top control panel then flipped it back from washer housing . Removed washer housing to expose main motor. Removed motor clips and screws . Removed motor coupling . Installed new coupling . Put it all back together . Works great!

Thurs. followed video directions, found the dogs to be defective and around 2 pm ordered dogs on line. To my surprise, on Friday around 11 am the dogs arrived. My husband installed them and the agitator is fine. I was so amazed at how quickly the dogs came. The machine was ready to go in less than a day. Thank you for your efficiency.

Follow the instuctions with the kit. Washer Machine Model # LSQ9244EQO.

I order the repaired kit and I use the old part where the dog cam goes due to the new one is loose.

Realized the new part was highly improved with the heavy metal insert to just screw on. Screwed it on to the existing extension on the unit and that was it! Five minutes!

Exactly as described in the sample video on your site.

Half inch ratchet extension unscrew remove replace cogs reinstall retainer ring drop back in . Watch how fast agitator spins.

I viewed the repair video provided and then dove into the project. I am sorry to say that the time suggested for the fix was a bit misleading. Took me less than five minutes rather than the fifteen minutes suggested. Thanks Parts Select for a great assistance in saving me an expensive repair call!

I looked at the video that was available for a general idea. I knew the exchange was fairly simple but it never hurts to watch someone else explain it. Used my socket and extension, some lube as recommended, replaced the pieces, tightened and turned the washer on. Worked like a charm. Thanks