Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RAS7233KQ0 > Instructions

RAS7233KQ0 Roper Washer - Instructions

All installation instructions for RAS7233KQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RAS7233KQ0
61-75 of 1,177
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Machiine would fill with water and then stop cycle. I determined that it was the lid switch because that is the sam e thing th emachine does when the lid is up.

  • Customer: Louise from Bridgewater, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 15 of 20 people found this instruction helpful
Followed some very handy instructions I found on the web.

First unplug machine and next back off the screws in the back of the plastic end caps holding down the control panel.
Then slip a putty knife under each of the front corners to release the panel so it can flip back
exposing the lid switch wiring harness clip connector.
Release the lid switch clip connector from the wiring harness.
Next release the two brass colored clips that hold the top to the sides.
Remove sides.
Remove screws holding lid switch and unclip switch from back of top nd from under top .
Remove switch and replace with new one.
Reverse order reassembly making sure the four base tabs of the sides are in the four slots in the machine base frame.
Reinstall brass clips.
Make sure new switch is clipped to the control panel harness.
Screw down corner screws in control panel end caps.
Done.

Thank you PartsSelect for your pormpt, courteous, and informative service.
You also had the lowest price and fastest delivery.
Well done!

Broken Lid Switch

  • Customer: Andrew from San Rafael, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 13 of 14 people found this instruction helpful
Washing machine is in a closet - tight space - was able to disconnect switch panel following other instructions, 2 screws on back, vertical // 2 screws near top corner on back, horizontal.

Pulled switch box off, could not get top sheet of washer off though, needed to detach side panel from back panel and lean the washing machine exterior panels fwd, and reach in from the back to disconnect the swicth ground, then pulled the lines, and disconnected the switch.

Then while still leaning the unit fwd, reconnected the ground for the new switch assemply, got it in the small clips leading back to control panel, fed the switch back into the control panel and reconnected.

Then, leaned unti back into place and got the panels lined up again, reset the control box, fiddles with the s clamps, and just tightened up the 4 screws.

Done.

shut off before finished

  • Customer: LARRY from LUCERNE, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 15 of 20 people found this instruction helpful
i knew the lid sw. must be bad and had a new one in hand, but when i remove the sw. ( near the lid ) i found the wires going back to where i could not reach. was not sure how to get at them so i repaired the sw. with tape untill i could find how to get at the wire end. after reading more in this repair area i know that i need to remove the control panel which is easy to do. next time i will read all i can on repairs in this section!!

Washing machine leaking water

  • Customer: John from Oklahoma City, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 14 of 17 people found this instruction helpful
First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconnected hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!

Washer did not spin.

  • Customer: Matt from Sussex, WI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 14 of 17 people found this instruction helpful
First I removed the two screws on the back side of the switch panel and tilted it back to expose the controls. I then pryed up the top of the washer to expose the lid switch. This was a mistake because I damaged the clips and bent the metal frame. Anyway after that I unlatched the lid switch on the top side, pulled it through the bottom, removed two screws holding the lid switch in place and replaced the switch and lid switch strike. Because I wrecked the machine top I had no alternative but to drill two holes from the top and put two screws in to hold the top down. It's ugly but it works.
The best part of all this is I received the part so fast that I was able to keep up the pace of doing laundry with no interruption. Thanks for being so reliable and quick to deliver. I already told many people about your service!

No cold water supply/slow cold water fill

  • Customer: Andrew from Virginia Beach, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 13 of 14 people found this instruction helpful
Unscrewed the two screws that hold the water lines to the valve. Unscrewed and lifted the control panel, popped the two spring clips that hold the back panel against the housing. Pulled the valve just outside the back panel. Took off the internal water line and moved it over to the new valve. Took off both hot and bold electric plugs and moved them to the new valve. With the old valve off, I sled the new valve into place and screwed it to the back panel. Put the spring tabs back on the back panel and screwed the back panel back together. Plugged it in, attached the water supply lines and tested it. Worked fine.

water leaking from pump

  • Customer: michael from westmoreland city, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 14 of 18 people found this instruction helpful
Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
The corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.

Leaking drain hose

  • Customer: Steve from Cypress, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 13 of 15 people found this instruction helpful
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.

bad lid swithch, problem with spin cycle

  • Customer: Bill from Beaver Dam, KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 17 of 27 people found this instruction helpful
remove 2 screws that hold timer section
remove large clips that hold lid section
repace lid swich and put back together
works good

would not spin properly even with new coupling

  • Customer: david from o, AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 15 of 21 people found this instruction helpful
Removed capscrew in end of agitator shaft took cover off machine-[ unscrewed two screws holding down control panel, hinged back, pryed retaining clips out, rocked back machine cover.]
Removed motor mounting clips and pump hoses, swinging motor and pump out of the way. Removed 3 capscrews holding transmission, pulled transmission towards me removing agitator shaft, disassembled clutch assembly - removing one cirlip then another, installed new clucth parts in same order

Lid Switch broke off at screws

  • Customer: Dale from West Branch, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 12 of 12 people found this instruction helpful
First off it was much easier after watching the video that was on PartSelect website. It was a very good description of how to do the repair. The main thing is to have enough room to be able to move the washer around and be able to get around it.. Our washer and dryer are in our 1/2 bath so we had to completely unhook the dryer to move it out of the way to have room to work around the washer.. It was still a tight squeeze but it was pretty quick and easy once we got the area where the lid switch is attached. The only trouble we had was putting the front of the washer back on the tub correctly. That was mainly in part with not having enough room to move around. It was easy enough that is was worth saving the service call from the repairman. The most help was watching the video. Thanks PartSelect for your help.

leaking drain pump. Obviously a common problem with this washer

  • Customer: John from Solana Beach, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench (Adjustable)
  • 12 of 13 people found this instruction helpful
Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the website parts diagram and whole website design is good.

Slipping Spin clutch due to leaking gear-case seal.

  • Customer: Thomas from Pascoag, RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 12 of 14 people found this instruction helpful
1. Unplug the machine.
2. Turn the water off.
3. Disconnect the supply and discharge hoses.
4. Open the cover and remove the cap/cover of the agitator. Use socket wrench to remove the bolt securing the agitator. Pull up on the agitator and remove it.
5. Lay washing machine down on it's front. Remove the inlet and outlet drain hoses from the discharge pump.
6. Remove the 2 "faston" connectors from the motor start capacitor (looks like a D cell flashlight battery). Rock the connectors back and forth and pull gently until they come off. Polarity doesn't matter but to be safe make note of the positions.
7. Press the release clip on the motor connector and pull to disconnect it. Move the wiring harness out of harms way.
8. Remove the 3 bolt securing the motor and transmission assembly to the bottom of the tub. Pull the drive assembly out of the machine and place it on a suitable work surface.
9. Examine the tub brake assembly (still on the bottom of the tub), the clutch assembly (on the motor/transmission assembly you just removed and everything else for wear or damage. Now if you decide to proceed with repair continue with the following steps. If not you're done.
10. Remove the inverted cup washer from the agitator shaft of the assembly. Remove the "U" clip from the shaft and remove the clutch mechanism from the drive assembly. Make a sketch of the position of each of the removed components to aid in reassembly.
11. Now you can see the gear case cover and it's seal. If it is leaking (as mine was) you will need to replace it.
12. With the assembly level remove the bolts around the cover and remove the cover. Place the cover on a flat surface and with a screwdriver or punch drive the old seal out of the cover from the outside in.
13. Clean the seal area and check for damage. Clean the cover and transmission housing surfaces of old gasket material. There is a factory sealant available for reassembly but I chose an automotive RTF @ $4 vs $24 and it worked OK.
14. Installing the seal requires some tools and experience to done successfully. The right size sockets or piece of pipe, coupled with an arbor press or vise will get the seal in. The cover is delicate so if in doubt find a machine shop.
15. Support the outside of the cover on a hard surface and with a socket or short pipe length, PRESS (don't hammer) the new seal into the gear case cover.
16. Make sure there is lubricant in the gear case. Not overflowing but maybe 1/2 full when view with cover off on a level surface.
17. Apply some RTV sealant to trhe cover and install it. Tighten bolts evenly. Light torque (1-2 ft-lb).
18. Reassemble washing machine and test for leaks and proper operation.

washer overflowing

  • Customer: GREIG from CARTERSVILLE, GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 13 of 17 people found this instruction helpful
Repair was easy enough by just unlocking the tab and twisting the switch out from under the control panel. For me though, this did not fix my overflowing issue. After more research I found the inlet valve needed to be cleaned out.
I respect that electrical parts are non-returnable as I am in the auto parts business.

Spin cycle not working properly; Clothes still soaked when spin cycle finished

  • Customer: Sarah from Columbus, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 12 of 15 people found this instruction helpful
We ordered both the motor coupling and the clutch assembly based on our troubleshooting, and because we figured both parts were inexpensive enough we might as well have them both. We initially thought it was the clutch assembly, but as we were taking the washing machine apart, we noticed that actually one of the bolts was missing completely and one had snapped in two. We then realized that the spin cycle problem was actually related to the instability of the motor because of the missing/broken bolts (they didn't even have washers!). All we had to do was replace the bolts and use a bolt extractor to get the broken bolt out, but we went ahead and replaced the clutch assembly as well for good measure. Everything ran perfectly after that! I was very skeptical to do the repair myself, but it really is easy, as long as you have someone with muscle to help out. You can also look up videos online that show you a step by step repair process for the clutch assembly, and I would highly recommend doing that so that you have a visual. It will make everything seem 100x easier.
All Instructions for the RAS7233KQ0
61-75 of 1,177