Models > RAS7233JQ0 > Instructions

RAS7233JQ0 Roper Washer - Instructions

All installation instructions for RAS7233JQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RAS7233JQ0
916-930 of 1,172
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer worked but wouldn't spin

  • Customer: Michael from Boca Raton FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Had a laptop with the repair video on next to washer and paused after each set of instructions to complete each task. Went perfectly! Only tricky part was fitting the cover back but eventually got it with a bit of jiggling. Very impressed with the instructional video as everything was where they showed it and came apart exactly as explained and more importantly went back together correctly.

was'nt spinning

  • Customer: Joseph from priestriver ID
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
It was easy with the video.I watched trouble shooting videos till i found the problem. wrote dwn the tools needed.watched video[lucky for me i would have forgot a step without it]orderd part, and was the hero

Would not spin out all the water from clothes

  • Customer: Michael from Tallahassee FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Similar to the youtube repair video, followed it mostly. This model has a different plug in set up on top where the wiring is. Just unplugged a different plug in a different location. The other difference is that I did a lot of dusting and vacuuming of inside parts and around motor. Also used some spray on rust converter on some rust spots then coated those areas with spray paint. Also where wire harness hooks to the frame I taped up a longer section of the wire to keep the wires together so they could move around and not be damaged. The actual repair took about a half hour, but took more time taking the washer outside on porch then back into the house. Out side repair is better because a significant amount of water came out of the washer and drain hose when we tilted it on the back to remove motor and transmission. Just follow the youtube video instructions and most people should have little or no problems doing the job.

Clothes soaking wet after wash cycle completed

  • Customer: Justin from O'Fallon IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the helpful video from PartSelect. Removal and Replacement of the Clutch Assembly was fairly easy. Just make sure you have enough towels to dry up any water that may come out after tipping the washing machine over. After Replacement the washing machine works like new. Thanks PartSelect.

Chlothes were coming out wet at the end of the cycle.

  • Customer: James from Bel Air MD
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Parts select gives you the top solutions for the problem you are having. This suggested a clutch, and upon looking at mine I could see it was displaced. I watched the instructional video, and it was spot on. It told me how to from beginning to end and it worked out perfectly. I spent about an hour of my time, spent $38, and my machine is fixed. Thank you Parts select for the free video, I couldn't have done it without it.

The washer would intermittently not spin for the last 5 months. Water would drain on the spin cycle but not spin. Read several websites on the problem but only one hit it exactly.

  • Customer: David from Wilmington DE
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
First watched YouTube video "Kenmore/Whirlpool washer not spinning", excellent video .Disconnected water hoses and drain hose. Unplugged the washer from the outlet. Removed the agitator from the washer tub then tipped the washer backwards resting on a secure block of wood for support not fully on the floor. Removed under insulation, removed both water pump hoses. Have towels ready when hoses are removed, there is still water in the hoses. Removed the water pump, disconnected the electrical connector from the pump motor, removed the bolts from the motor that attached the motor clips, removed the motor clips from the bracket and removed the motor assembly. Video shows motor, bracket and gearbox removed as one unit. Very heavy. Remember motor position on the bracket for reassembly, I used yellow marker. Removed the bracket the mounts the motor. Removed the bolts for the gearbox and began to lower the gearbox. The agitator shaft on the gearbox is pretty long so I had to tilt the washer some more to remove. After the gear box was removed I could now see the spin clutch, which according to the video was definitely bad. PartSelect had the correct part, reasonably priced. Ordered normal FedEx delivery, part arrived in 2 business days. Instructions came with the part for very easy installation. Installed the new clutch and reassembled the washer. Before reconnecting the washer hoses and drain, I plugged in the washer, manually placed timer on spin, washer spun, could not see spin but felt washer in spin cycle. Reattached water and drain hoses. Filled washer empty with cold water and placed timer again in spin cycle. Water drained, no leaks under washer or from hoses, spin cycle good. Repair done, works great.

The washer wouldn't spin out

  • Customer: Karla Ann from Neenah WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
went to you tube and watched a video on how to take it apart and replace the clutch assembly.

would not spin

  • Customer: Richard from Somerset PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the the drain hose from the pump. Removed nut from the agitator. Then laid the washer on its back after removing the inlet hoses. took out the pump, remove wire harness from motor then removed the motor. removed the three bolts holding in the the transmission. The one mistake I made was that I removed the springs for the brake shoes and this cause me to have a lot of trouble trying to put them back on. Once the clutch arrived, I removed the old clutch from the transmission shaft, and installed the new clutch using all the parts that came with it. Then put everything together in the reverse order that they were removed in.

Would not spin during spin cycle.

  • Customer: James G from Crossville TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After watching the repair video by partselect.com I followed the directions exactly. It turned out to be a piece of cake. I found out that partselect.com has many, many do it your self repair videos on youtube.com. I intend to use them for future repairs. Thank you partselect.com.

Clutch went out

  • Customer: David from Colorado Springs CO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Just watched the video provided by parts select and then went to work. Excellent video. If I had been better mechanically inclined it would have been much faster. Thank You Parts Select! Also fast shipping.

The spin cycle got weaker and weaker and it couldn't spin the wash.

  • Customer: Mark from Middleboro MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched a vidio on YouTube and figured the problem.then I tryed to find the clutch local but no luck! So I yahooed it and found this web sight,I ordered the the part and it came in a few days.The part showed up on a Friday and I put it in the next morning.I watched the link your parts sight refered me to and was very good ! I got all the tools together and started the project,it wasn't the exact same unit but it showed you enough to figure it out.I ran the vidio as I did the project and it went smoothly.I am very happy with the parts, the web sight and the lincks it shared with me . I booked marked the sight for future reference and have already shrared it with someone who has the same problem. thank you for all the help!

pumps water but will not spin

  • Customer: walter from grove city PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I did repair myself with your instructions. it was very easy to do for my age. 84.

would not spin in spin cycle.

  • Customer: paul from wardensville WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watch the video on the part ordering webpage.

My washer stopped spinning.

  • Customer: Jacob from Champaign IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I researched the troubleshooting on PartSelect.com and determined the clutch was going out on my direct drive Whirlpool washer. I ordered the part, found the instructional video that actually had my exact washer being worked on, I followed all of the steps of replacing the clutch and in a snap, my washer was spinning. I've worked in apartment maintenance for years and PartsSelect.com has always been my only resource for appliance parts and repairs. The prices are great (I've compared most parts websites and 8 times out of 10, partsselect.com is cheapest), the shipping is extremely fast and the parts are alway right. Great site!!!!

THE SHAFT ON THE DIRECT DRIVE WAS WORN

  • Customer: ALLEN from Newton KS
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
REMOVED THE CONTROL PANEL AND THE CABANIT.THEN REMOVED THE ADJUTATIOR .REMOVED THE MOTOR AND GEAR BOX SLID THE OLD SHAFT OUT AND PUT THE NEW ONE IN PUT BACK TOGETHER. TOOK ABOUT ONE HOUR .
All Instructions for the RAS7233JQ0
916-930 of 1,172