Models > RAS7233JQ0 > Instructions

RAS7233JQ0 Roper Washer - Instructions

All installation instructions for RAS7233JQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RAS7233JQ0
61-75 of 1124
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Found cracked brake shoe

  • Customer: Michael from Trafalgar IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 11 of 14 people found this instruction helpful
Remove the main bolts that hold the gearbox in place, pull the gearbox and shaft out. You will see the brake shoes and drum--the large spring is a struggle to replace. Getting it out was not hard. The biggest struggle I had was replacing the brake shoe spring after replacing the shoes. I ultimately compressed the spring in a vise, then used safety wired it, then placed it between the shoes, then cut the wire to relaease the spring.

Broken Lid Switch

  • Customer: Andrew from San Rafael CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 10 of 11 people found this instruction helpful
Washing machine is in a closet - tight space - was able to disconnect switch panel following other instructions, 2 screws on back, vertical // 2 screws near top corner on back, horizontal.

Pulled switch box off, could not get top sheet of washer off though, needed to detach side panel from back panel and lean the washing machine exterior panels fwd, and reach in from the back to disconnect the swicth ground, then pulled the lines, and disconnected the switch.

Then while still leaning the unit fwd, reconnected the ground for the new switch assemply, got it in the small clips leading back to control panel, fed the switch back into the control panel and reconnected.

Then, leaned unti back into place and got the panels lined up again, reset the control box, fiddles with the s clamps, and just tightened up the 4 screws.

Done.

No cold water supply/slow cold water fill

  • Customer: Andrew from Virginia Beach VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 10 of 11 people found this instruction helpful
Unscrewed the two screws that hold the water lines to the valve. Unscrewed and lifted the control panel, popped the two spring clips that hold the back panel against the housing. Pulled the valve just outside the back panel. Took off the internal water line and moved it over to the new valve. Took off both hot and bold electric plugs and moved them to the new valve. With the old valve off, I sled the new valve into place and screwed it to the back panel. Put the spring tabs back on the back panel and screwed the back panel back together. Plugged it in, attached the water supply lines and tested it. Worked fine.

Washer stopped mid cycle

  • Customer: Travis from Pearland TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 12 people found this instruction helpful
1. Unplug washer.
2. Remove screws at control panel end caps.
3. Flip control panel back to expose wiring.
4. Detach lid switch wiring harness from control panel.
5. Use screwdriver to pry the 2 brass clips holding the back panel of the washer to the front and sides piece.
6. Tilt the front/sides piece over to expose lid switch.
7. Use nutdriver to detach ground wire.
8. Use screwdriver to remove 2 screws holding lid switch in place.
9. Install new lid switch. Make sure wiring harness piece is facing the right direction.
10. Put washer back together in same order it was disassembled. Make sure front/sides piece connects to the clips at the bottom.

tub off center, rubbing on outer tub in spin

  • Customer: Charles from Rose Bud AR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers
  • 9 of 9 people found this instruction helpful
turned the washer on it's back and shoved the tub to the side to release pressure on a spring ,pulled it loose and installed new one. this worked for the back two then turned washer on it;s face and repeted the process on the front spring.
Washer works great now.

Leaking drain hose

  • Customer: Steve from Cypress CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 10 of 12 people found this instruction helpful
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.

Lid Switch Asembly broke

  • Customer: Brooks from Plano TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 15 people found this instruction helpful
First off I would highly recommend the review by Dennis From Evans City PA. This was quite helpful.

The problem is the lid switch assembly is glued together and the original part came apart and needed to be replaced. The symptoms described by others were accurate so we opted to replace it.

On my machine there are two screw on the front corners of the panel where the dials attach to the top of the washing machine. I removed those two screws and by lifting up and forward was able to move the whole thing out of the way.

You should see the connection from the dial panel running down into the wash basin. This is where you will unplug the old switch and replace it with a new one. There are little plastic clips that hold it in place, but you can squeeze them with your fingers to remove it from the panel.

In order to get access to the underside where the wires are connected you will need to remove two clips that hold the back pane to the rest of the sheet metal. In my case I wasn't quite prepared for the entire frame to move but once the clips are removed the back panel is completely removed and you can pull it forward to gain access to the underside.

Once you are able to get underneath you will see a screw that holds the ground wire. This is the one that you may need pliers to remove. There are two screws that hold the switch in place but you can access them at any time. I had already removed the old screws by this point. This should leave the switch disconnected from everything and you can install the new one.

Now just connect everything back together. The two screws for switch where the lid hits. Connect the ground wire and run the the connection back to the top portion where it will connect back up to the top panel.

I would add that there are two thin plastic strips that ran vertically up the back fo the back panel that meet the outer casing. I had to re-seat these before putting the clips back on the top.

Unbalanced and walk across the floor on spin cycle

  • Customer: James M from Elkhart IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench(Adjustable)
  • 12 of 19 people found this instruction helpful
Part Select provided the problem determination information and the video on how to install the replacement parts. I ran into one problem, I could not remove the lock nut to remove the inter and outer tub. I should have bought the special wrench for $14, no local DYI or hardware store had the wrench. So, after examination I used a large screwdriver and wood block to lift the tubs up just enough to remove the old pads and replace with the new. The old pads showed only a wear, but was enough to spin the tubs off balance. The new tabs made the washing machine work like new. New washer $500, repair man $150, parts and information from Part Select $20 bucks, priceless.

Washer would drain, agitate but not spin and was very noisy and would vibrate heavily

  • Customer: Michael from Schuylkill Haen PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 9 of 10 people found this instruction helpful
I first watched the youTube vidio on yhe PartSelect web site. After getting a visual of the repair, I decided to tackle the job with a better understanding and knew the repair was easy to purform. First I took the two screws out of the contrl panel on top of the washer, rolled the panel back to expose the clips that hold the metal cabinet to the back panel of the washer. After removing the cabinet I was ready to lay the washer on it's back and had a clear view of the pump, motor and clutch... I was able to easly identify these parts because I took time to watch the video. Using a flat head screwdriver I removed the clips that hold the pump to the motor... Without disconnecting the hoses connected to the pump I pushed the pump to the side and out of the way. This further exposed the motor. Using the flat head screwdriver, I removed the clips holding the motor to the transmission (they just snap off like they did on the pump). The motor was now ready to be removed from the transmission ( it just lifts off) before removing it I disconnected the power suply wire from the motor... Now the motor can be completely removed. I identified the drive couupler 1/2 was on the motor shaft the other 1/2 was on the transmission shaft.. On both halfs the splines were broken. I removed the old broken drive coupler. Since I already had the machine so far apart i figured i would replace the clutch also. Using a deep socket ratchet wit an extention I removed the agator... I then unbolted the transmission (only three bolts) I gentely pulled the transmission and shaft out of the bottom of the washer. This exposed the clutc assembly, I removed the clutc ( which wasn't bad or wore by the way) and replaced it.... I figured I had it and I was this far into the repair why not. After relpasingvthe clutch, I slid the shaft and transmission back into place tightened the bolts and that was done. I then slid/replaced the drive coupler... Placing one half on the motor shaft the other on the transmission shaft, placed the rubber bushing on the oneside of the plastic drive coupler. And mounted the motor back on the transmission utilizing the clips I took off earlier. Once the motor was in place I installed the waterpump fastened by the clips. Flipped yhe washer up, replaced the cabinet... Tightened down the the control panel and was ready to do some wash..: the washer runs perfect now and I saved myself about $700.00. It was allot easier than I thought it would be... Watching the youTube video is the secret to success. The washer is running like the day I bought it new... All for only 53.00. Hats off to everyone at PartsSelect for going above and beyond. Regards, ~ Michael

Wash machine, wouldn't spin dry the close. The pump still worked to drain the water.

  • Customer: Matthew from Albany MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 11 of 17 people found this instruction helpful
Unplug power from wall.
Disconnected water lines
Tip Unit on it's side. (Recommend turning so motor is to the top side)
Disconnect Electrical connector and Hoses from the pump and motor.
Disconnect metal straps used to retain the motor to the transmission. (screwdriver to pry)
Remove old coupling pieces from transmission/motor(used a long screw driver, rock back and forth)
used air compressor to clean up electric motor
replace new coupling on motor and transmisison (may need hammer to tap into place)
set rubber bushing on transmission side (transmission shaft should be facing up at this point)
replace electric motor into place, making sure to line up bushing and motor mounts.
replace metal strap connectors between transmission / motor (this can be tricky, as the one in the back is hard to get at.)
replace electrical connectors and hoses
connect washing machine power and water and test

my cold water did not run in the machine and it would not rinse

  • Customer: TONYA from DISTRICT HEIGHTS MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 11 people found this instruction helpful
we looked at the video first then my husband fit the proble boy! was i excited! all the stores tried to get me to buy a new one. thanks partselets!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Replaced ring that broke and washer that was bent on the edge.

  • Customer: Kim from West Liberty OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 15 of 29 people found this instruction helpful
Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and started stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).

would not spin properly even with new coupling

  • Customer: david from o AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 10 of 15 people found this instruction helpful
Removed capscrew in end of agitator shaft took cover off machine-[ unscrewed two screws holding down control panel, hinged back, pryed retaining clips out, rocked back machine cover.]
Removed motor mounting clips and pump hoses, swinging motor and pump out of the way. Removed 3 capscrews holding transmission, pulled transmission towards me removing agitator shaft, disassembled clutch assembly - removing one cirlip then another, installed new clucth parts in same order

improper or no hot water flow

  • Customer: Cynthia from Manchester MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 10 of 15 people found this instruction helpful
After taking the entire washer apart one time, we learned that we could take the top and front of the machine off only to repair it. I found Part-select online and with the model number locating the part was easy. It arrived within 3 days and with instructions I could easily replace the old part with a few tools. I spent dollars instead of hundreds for a new machine.

water leaking from pump

  • Customer: michael from westmoreland city PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 9 of 12 people found this instruction helpful
Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
The corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.
All Instructions for the RAS7233JQ0
61-75 of 1124