Models > RAS7133KQ0 > Instructions

RAS7133KQ0 Roper Washer - Instructions

All installation instructions for RAS7133KQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RAS7133KQ0
1,096-1,110 of 1,168
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

dropped the ground screw, trying to find it

  • Customer: James from Liverpool NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Had some problem aligning & installing the bottom of the cover. Put together and took apart. Double check that both sides on the bottom front are engaged. COULD NOT HAVE DONE THE JOB WITHOUT WATCHING YOUR VIDEO !!!! THANK YOU !!!

Leaking water from under the front of the washer

  • Customer: John from Morgantown WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Used pliers to help disconnect hoses, unplugged power cord, laid washer on its back, unsnapped two clips holding pump to the motor, lifted pump off, and replaced it.

Water would'nt shut off

  • Customer: John from Upper Sandusky OH
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Video made it easy

Water leaking from under front of machine

  • Customer: Kevin from Avondale CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After watching the video and reading some of the instructions posted on Parts Select I disconnected the power cord, shut off and disconnected the water lines before laying the washer down on its "back" with help of a dolly.(IF you don’t own a dolly this can still be done without one but I recommend having a friend help you depending on your age and health) Once I had the washer laid down it became apparent to me that I didn’t need to take the whole "cover" off but could do the repair from the bottom of the machine. Following the instructions I first removed the hose clamps from the hose running from the pump to the tub and the hose that runs to the back of the machine where the drain to the wall attaches. I then "popped" the two clips off the pump as described in the video and after removing the pump I turned the clips to the side and removed them as well. At this point I removed the clamp from the "pump to tub" hose on the tub side and then removed the hose. I followed this up by removing the entire hose assembly that the "pump to drain hose" hose attaches too. Once you've seen this "assembly" you'll understand what I mean. Anyway, once that was done and the new parts had arrived (parts came quickly I placed my order on Thru evening and received them on Tues with the Labor Day weekend in-between) Install was as simply as removal, I laid the machine down using the dolly and then simply installed everything starting with "pump to drain hose assembly" then the "tub to pump hose" then the pump itself and finally both hoses to the pump. The "pump to tub" hose came with two new clamps however they are the type of hose clamps requiring the use of a screw drive to tighten not the original type it had on it that you just squeeze with pliers. I used the new ones that came in the package. The other hose didn’t come with a clamp and only has one where it connects to the pump, so I reused the original. I would suggest that you also check or just replace the drain line that runs from the machine to the wall at the same time as the rest of this repair as I did not and the 1st time I ran the machine that hose sprung a leak.

leaking water pump

  • Customer: Erin from Annapolis MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After removing the outer shell of the machine, and disconnecting the supply hoses, I leaned the machine on it's back and disconnected the drain line. Then, it was simply a matter of removing and replacing the damaged pump with the new one. The pump is held in place by two easily removable clips. The hardest part of the whole process was making sure the shaft from the motor lines up with the corresponding hole on the pump.

Bad Motor Coupler

  • Customer: Hilary from Gainesville FL
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
So, the instructional video was great but be warned that you REALLY need to hammer the part into place. Basically hammer it into place so that the end of the shaft that it goes on is flush with the plastic piece of the coupler on both ends. Otherwise, you'll put the washer together and run a load and it'll squeal and smell like burning rubber. We had to take it apart like 3 times before we got it on there securely enough. We would then run an empty load and it would be fine but as soon as we would add clothes the squealing and burning would ensure. So, my advice is to hammer it in well and save yourself the time and struggle!

The washer would turn 45° by finish spin

  • Customer: Fred from Hico TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
With no broke springs I thought that they might be weak so I ordered them but didn't install them as I found that the basket had a drag at one point of turning it, so I took it down to the clutch and found the nylon arm that released the brake had the small pins broken off. This would cause the brake to not release full enough that the eccentricity in it had a drag spot during the spin causing tremendous vibration. To disassemble I took the transmission off and the basket off and install new clutch assembly with the basket laying horizontal on a table. I did notice that the new clutch only had three pads on the band and the old one had six. I called you back with no satisfaction, but was given the phone # of the manufacturer and they confirmed that theirs had six pads but the part # checked out so I installed it. It now sits basically still during a cycle. I made and supervised the making of parts in a machine shop all my working carrier and I don't understand the weak link of the nylon pins milled / molded on a part that takes a lick from the actuator every cycle. It appears to me it was made to break, but it is about 20 years old. Thanks for your video help on the tube. Fred

Supply of cold water not flowing normally

  • Customer: Will from ARLINGTON TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Found part needed in partselect website, watch the video after i opened the rear panel ( i should have watch the video before doing any work :( ) that will much easier. after replacing part my washer is now working like new :). Thanks PartSelect. next project dryer ;-))

water was dripping into tub

  • Customer: Peggy from Brick NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
took it apart and put in the new valve

Washer woulp not spin, brake cam driver not like video

  • Customer: Jody from Elk Creek CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
changed parts easily, following the video. Problem was the BRAKE CAM DRIVER, the plastic piece that fits around the shaft near the drum. The old one was visibly torn up, the pegs worn off, the whole thing worn down. The problem with the repair was the video showed an "E ring" holding it on and my washer had no E ring, had nothing hold it. It just sat there. Installed it anyway, although I was worried it was too loose. Sure enough there was a problem. it spun initially then started that ugly clicking noise. turned off washer immediately, disassembled again, and prayed. I found a large flat washer to take up the slack between the clutch and the plastic brake cam driver, reassembled, tightening the nuts a fair bit tighter than before. both the nuts on the transmission and the nut on top the agitator. works perfect!

direct drive motor coupling

  • Customer: Eugene from Chiefland FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unplug washer. turn hot and cold water off. disconnect and mark water hoses. put a blanket on floor and lean washer on its back. use screw driver to remove metal clamps from water pump. use ratchet or nut driver to,,remove screws from metal clamps on motor.remove metal clamps with screw driver. unplug wire harness from motor. remove motor and remove old drive coupling and repelace with new part.

would not spin

  • Customer: Richard from Somerset PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the the drain hose from the pump. Removed nut from the agitator. Then laid the washer on its back after removing the inlet hoses. took out the pump, remove wire harness from motor then removed the motor. removed the three bolts holding in the the transmission. The one mistake I made was that I removed the springs for the brake shoes and this cause me to have a lot of trouble trying to put them back on. Once the clutch arrived, I removed the old clutch from the transmission shaft, and installed the new clutch using all the parts that came with it. Then put everything together in the reverse order that they were removed in.

water leaking from unit

  • Customer: Glenon from Saint Petersburg FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
unplug electric cord. shut off then disconnect hot and cold water hoses from nozzles. place drain & water hoses over washer. place washer on floor( back/hose side down). use pliers to remove hose clamps(2) from pump. unfasten metal clamps(2) from pump. remove & replace unit. reinstall by reversing process.

Washer was leaking

  • Customer: Gregory from Colleyville TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the video and everything went exactly as the video said! Just follow the video to a tee!

no spin dry

  • Customer: Walter from West Palm Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
... exactly as shown in the video in addition to shutting water, removing hot & cold lines & waste tube. I was amazed at how fast the parts were delivered in two days regular shipping. Machine now purring a wifey happy once again! Thanks for the great service & video! I recommend PartSelect highly! WSD
All Instructions for the RAS7133KQ0
1,096-1,110 of 1,168