Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RAS6233KQ0 > Instructions

RAS6233KQ0 Roper Washer - Instructions

All installation instructions for RAS6233KQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RAS6233KQ0
1,096-1,110 of 1,177
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer would not spin or agitate.

  • Customer: Gerald from White Cloud, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
electric unplugged, removed water lines. two screws on back of control housing removed, tilted housing back, removed two clips on top of washer housing, removed body. tilted washer backward, removed brackets on water pump and electric motor, pulled motor off and removed broken parts on shaft, replaced with new parts. Lining up motor shaft to washer was a bit tricky but time and patience got it togather. replaced brackets on motor and water pump. put washer upright and put body back on the body has to be set on guides correctly or will not set right. replace clips andtilt top down and screw it. hook up water lines, and electric.

Would not spin,but would fill and drain and could hear motor and trans worked

  • Customer: Diana from Sherborn, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Follow instructions in part repair video from part select,but put washer on back first to see if can access area without removing the whole outer cover we did not even need to do that step only took 20 minutes to replace coupling. The video was great

Washer wouldn't spin and we could see coupling was broken

  • Customer: Sharon from Marina, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We watched the how to video...repair took less than 15 minutes. You can't go wrong if you just watch the easy to follow video! Washer works as good as new.

Washer was not spinning, but making a loud spinning noise.

  • Customer: William from Sonoma, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Disconnected power. Disconnected hot and cold, and drain hoses and placed in a plastic bucket. Pulled cover off the washer. Tilted washer onto its back. Removed 2 clips holding the pump. Disconnected wire harness from motor and removed 2 clips holding motor starting with lower clip. Removed a screw from the upper clip used for shipping. Set motor aside and removed broken pieces of the motor coupler from motor and transmission. The replacement part had a metal sleeve in the center of each white plastic ring. The old part did not. This required tapping the new ring onto both the motor and transmission shafts with a socket and makes for a tight fit. Reversed the process to put everything back together. Some alignment might be necessary to place motor to transmission. I recomment wearing thin work gloves to avoid nicks from sharp edges. I didn't. Washer is spinning again and sounds a lot better.

The washing machine basket wouldn't spin

  • Customer: Kali from Missoula, MT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Remove the cover of the washer, pull out motor, pry out motor coupler, replace. May have to hammer with a rubber mallet to get it on. Replace motor and washer cover. We also replace the water pump. It wasn't broken, but since we had the washer torn apart, decided to replace it as well. There are lots of YouTube videos to help you out.

no spin out of water in drum

  • Customer: james from dumont, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
followed the video on the web site and repair was amazingly easy. I have two of these machines, and this same part went bad about 1 1/2 year ago, so this time i was ready for everything. Took everything apart, got rid of old broken part, replaced with new, and Bam, washer back up and running, less than 30 minutes, I am limited on space in my basement, so i didn't turn machine on its back, i did it in the upright position, just utilized some wood blocks to hold the motor during part change, and a hand spring clamp to hold pump and hoses out of my way after removing the clips that hold it on. It's not rocket science, if i can do it so can you. Good luck

Loud screaching noise occured during use

  • Customer: William from East Northport, NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed written instructions after viewing repair video. Would have been helpful to know how far onto shaft each drive piece needed to be placed. I should have noted old piece placement, though if this was noted in instructions it would have been reassuring to know what is the proper placement. I also placed machine on its back to align the motor and transmission after new parts were installed on each.

Washer was not agitating and no spin cycle

  • Customer: Michael from Doylestown, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
The repair was easy and the video tutorial was great. That was the easy part. I also had to replace the drain pan and getting it in and out of the pan is no easy task. Plus when you have not moved the washer in 10 years there is some cleaning to do. I would not hesitate to do it myself again. It cost me $20 and some sweat equity.

The tub suddenly stopped moving after the final rinse, before the final spin.

  • Customer: Raymond from Chagrin Falls, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watched the video to get a good idea of the procedure. I followed the instructions to remove the cabinet but kept the washer upright on its base. I left the water feed hoses attached to the wall spigots, but turned them off. The pump was rusted onto the motor shaft so I left it there. I unhooked the pump hoses from the pump so I could remove the pump and motor as a unit. The plastic coupling ends pulled off the motor and gearbox shafts easily. The new coupling ends have metal inserts which are a tight fit on the gearbox and motor shafts. To maintain the original alignment it's important to drive them fully into place. I greased the shafts then tapped the coupling ends on with a hammer and drift. The drift was a metal tube, inside diameter slightly larger than the shafts, but small enough to bear on the metal inserts, not on the plastic. My diagnosis was wrong - the original coupling was in good condition, but the clutch had failed.

Tub will not spin

  • Customer: Rick from Terre Haute, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After finding out the tub would not spin, I removed the washer to find broken pieces on the floor. I did a google search on my model number and found that the problem was the direct drive motor coupling (it matched the pieces on the floor). So, I watched the "how to" video and I followed the steps verbatim. I found the coupler missing and the plastic pieces on the drive broken. My order came in quickly (within 48 hours) and my washer was running in 20 minutes after receiving the package. It has been great ever since.

Tub was spinning only part time. Had to have help getting started

  • Customer: Kingsley from Ewing, IL
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Installed new clutch assembly and while I was at it replaced the Motor Coupling. Actually, I had a good time doing the repair. I am almost 80 years old, so had to have help laying the washer on backside. Got a small stool from which to work (back problems). The only thing I found the least bit difficult was reinstalling the retaining clip for the clutch assembly. The rest was a piece of cake. Were I to do the same repair now, it would take less than 30 minutes. Washer works like new now. Very proud of what I was able to accomplish. Of course, need to watch the repair video so you will know where to start.

Motor Coupling Broken

  • Customer: Jeff from Nicholasvile, KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the 'how to' video, stopping the video when needed to complete a portion of the repair. I was doing the repair in a laundry closet, which took me a little longer, but with the right parts ordered and the instruction video this project was easy and does not take very long.

Washer full of water not draining

  • Customer: James from Port St Lucie, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
First I tried take the back off. Wrong move, wasted 30 mins on that. Then drained water into bucket, moved washer on hand truck to garage for more room to work. Had pump & drive coupling out in 20 mins. Found Partslect & ordered parts in 15 mins. Two days later had everything back working in 20 mins. Very Good Srevice.

The tub would not spin during the spin cycle. I diagnosed that the door switch was functioning. And through some reading on the internet, found out it was the motor coupling. I replaced the clutch assembly strictly as preventative maintenance.

  • Customer: Jorma from Saint Cloud, MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I am not even going to attempt to explain. The videos that were brand specific are all anyone needs to complete any repair. They are very well made. And easy to follow. Thank you for saving me a repair call!

The washing machine started making a clicking type noise and would not drain after the rinse cycle completed.

  • Customer: Larry from Buffalo, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After entering the Parts Select website and searching for the model number information, I found a video which described the problem. The video explained the step by step procedure to access the possible problem. The problem was exactly as the video described, I ordered the repair part, made the repair, and placed the washer back in service. Oh, by the way, the part was delivered to my house the next day.
All Instructions for the RAS6233KQ0
1,096-1,110 of 1,177