Models > RA724K1WH > Instructions

RA724K1WH Hotpoint Range - Instructions

All installation instructions for RA724K1WH parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RA724K1WH
91-105 of 108
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Live in an apartment and they had generic drip pans on the stove causing pots to tilt when cooking.

  • Customer: Jennifer from Cleveland OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced drip pans that the apartment Superintendent had in place with the correct drip pans and now cooking is beautiful again! No more uneven cooking on the stove top.

Burner switch shorted out

  • Customer: Robert from Blairsville GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This burner is on a Monarch wood and electric range. The 8in burner shorted out and fried the switch. I had to remove the cover over the switch's. I marked each lead with paper and stapled the paper to the leads. When the switch came in I just had to reattach the leads.

Burner would not turn off

  • Customer: Thomas from Winter Garden FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The burner light did not turn off, and the rear burner stayed hot. Unplugged unit and removed switch, which turned off the "burner lit" lamp. Thus I figured it was the switch that was causing the problem. Ordered the switch (I think around $18 and plugged it in. I think there were 4 screws to get the panel off, and then another 2 to get the switch off. When I plugged the unit back in (it had been unplugged while I waited for the part to ship) it beeped for a while. I had to turn the breaker on and off, and that solved the beeping problem.

Oven Door Handle End Caps.

  • Customer: Linda from Lake Panasoffkee FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I purchased my stove second hand. It was a mess but I saw a gem under all that dirt and grime. It took me a week and it looked brand new. The end caps on the oven door handle were discolored and cracked. They made the stove look old. It was an easy repair and my stove looks brand new. I will order an extra set just in case as these parts are getting harder and harder to find. I am so pleased with the original parts. They were here with in days and well before promised delivery date.

Burner light would not go out.

  • Customer: Creed from Topsham ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Identified the switch that went bad. Order a new one and replaced it. The part came in a timely fashion and I am pleased with the result.

Burner Terminal had shorted out out.

  • Customer: Daniel from Wheat Ridge CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
had to pull range away from wall and unplug it so we could get behind to access the rear panel. we then removed old terminal block, by, removing screws from back panel, and one screw from under burner drip pan, inserted, new block, and reassembled. plugged it in to test and burner worked properly.

Burner switch went out

  • Customer: Jim from Prosser WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
turn off power at main electric panel/ Move stove away from wall and unplug cord from outlet. take knob off the front take two screws off the panel, take back panel off and remove the used switch and take and replace the wiring to the new one , one at a time wire for wire. Then put back tighter in reverse of the way you took it off. plug in cord and move stove back to the wall. Easy

surface burner would not work

  • Customer: julio from hobbs NM
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
watched it on parts select this is a real fast and simple install took longer to pull the range out of its position well started by shuting off the power then double checked that the range was deenergized removed the knob then the 2 screws then on the rear of the range removed the back panel about 8 screws used a nut driver then removed the old switch removed each wire one by one and pluged each wire into the new switch just as they were on the old switch the new switch was exactly the same so every thing matched up perfect installed the screws to the front which hold the swich in place then the back cover turned on the power and tested the switch every thing working ok done shut off power slid range back into its place turned power back on everything still ok

2 mounting bracket included, wires too long

  • Customer: Fuad from Sarsota FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I couldn't tell which one work best till I installed 2 units and I liked the other bracket for stability.The wired were too long and there is not a given way to strap them and keep them away from the heat source.

GE Electric Range rear left burner quit coming on

  • Customer: Richard from Richmond TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed the back top cover with 1/4" nutdriver. Removed the burner terminal block with 1/4" nutdriver. Within 15 minutes had the terminal block kit removed and installed and in service.

Connector to burner is out.

  • Customer: Jonathan from Lynn MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remove old wire and replace new wire into place.

Corroded connectors and melted block on an electric stove.

  • Customer: Jacqueline A from West palm beach FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
The original GE blocks/wires were color coded to specific burners. The new ones are not color coded since they are sold individually and work with any burner, but they were identical to the originals in every other way. Just remove old blocks one at a time and connect the replacement so that the burner is connected to the proper control. Since the stove age was unknown, I replaced all four blocks to eliminate a repeat of the problem later. The screws holding the blocks and the wiring cover on the stove back require the same small socket wrench; not enough room in some places for an adjustable wrench. It took no more than 20 minutes to replace all four, test the burners, and close up the back wiring panel. The instructional video on the website eliminated my hesitation to tackle this repair. The parts arrived the next day, with no special shipping service requested. WOW. PartSelect will be the first place I go to find what I need for the next fix-it. I'm almost looking forward to something else breaking. LOL. Thanks, PS.

BURNER WOULD NOT TURN OFF

  • Customer: BILLY from WEBSTER FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
REPLACE CONTROL SWITCH

one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.

  • Customer: brendan from lebanon NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

The terminal block for a front stove top burner failed

  • Customer: Tom from Kensington MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
There was an excellent video demonstrating a very good method for replacing the terminal block at Parts Select.. I ran into a problem with the kit. The wires were too short. Instead of replacing the entire wire I needed to clip off part of the old wiring and solder the kit wires to them. I also needed to insulate the connections with electrical tape to prevent them from shorting out.
All Instructions for the RA724K1WH
91-105 of 108