Models > RA724K1WH > Instructions

RA724K1WH Hotpoint Range - Instructions

All installation instructions for RA724K1WH parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RA724K1WH
76-90 of 99
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

none to occasional power to burner elements

  • Customer: Mohammed from San Jose CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Exactly followed the instructional video and my installation was flawless. Now the burners power up and function like new. The whole repair was smooth and easy.

One burner didn't work, others were failing

  • Customer: Ronald from Minneapolis MN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I simply followed the instructions on the PartSelect website. Since the range is 20 years old, I replaced all four terminal blocks. I used needle nose pliers to carefully nurse the old terminals off the burner controls, and used fine sandpaper to burnish the male contacts on the burner controls. Since the failed terminal block wire had overheated, I burnished the burner contacts that slip into the terminal blocks to eliminate any resistance that could cause overheating. So far, all burners are working great!

The burner would not work.

  • Customer: Sue from Fort Oglethorpe GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I pulled the range out, unplugged it, took the back off, unplugged the old terminal block and removed it. Attached the new block and ran the wires through to the back and plugged them in. Reattached the cover on the back of the range, plugged the range back in and pushed it back into place.

Two surface burners did not work

  • Customer: Ervin from Dublin GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Removed the two screws from the range's top and the rear zinc cover and replaced the two front clip receptacles. It took me 30 min to finish the job.

left rear element not heating up

  • Customer: Anibal from Lakeland FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I pulled range away from the wall and pulled the electrical plug. I removed all of the heating elements and raised and secured the top panel.I then removed the one screw that held the terminal block in place.now I went to the rear of the range and remove six screws that held the top cover in place.I now cut the two wires going to the old block,I pushed the new wires through the back panel.I installed the new terminal block using one screw. Now I went to the rear and removed the old wires and installed the new wires. I rolled up excess wire and secured with plastic ties. I installed the rear cover using six screws,I put electrical plug back into outlet,pushed range back in place,lowered front panel,replaced all the elements and turn on left rear element.FINISH EVERYTHING WORKS. P.S. I ordered two terminal blocks,if it happens again in any of the blockes I'll be ready. total costs for both $25.55 plus shipping.

Burner went to high heat at any setting

  • Customer: Robert W from Whitehall PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Thanks to Partselect's instructions the repair went very easy. When I was done and the wife finished cleaning the sides of the stove and the floor behind it, I was surprised after I plugged the stove back in and noticed the clock was only 18 minutes off! Awesome company to deal with, Thanks!

Replacment of burner control switches

  • Customer: Judith from Keezletown VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!

Old Surface Burner Block Kit Disintegrated

  • Customer: Kevin from Aurora CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Very easy. Followed the video instructions. Unplug stove. Cut old wires. Tape new wires to old wires to facilitate pulling new wires thru old hole to back of range. Removed back cover. Pulled old/new wires thru to back. Removed old connectors. Attached new connectors. Replaced back cover. Screwed new terminal block to front of range at burner. Attached new burner. Plugged in stove. Replaced stove in counter.

Burner not heating

  • Customer: Henry from Norwich CT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed old socket, I had replaced with a aftermarket that really did not work well. When I recieved the terminal block kit from your company it was the proper kit. Service was better than expected, part and price was great and it took very little time ti install. Thank you.

Bad connection to electric elements

  • Customer: Larry from Salem IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Lifted top, opened back splash, unplugged old wires and replaced with the new ones them connected to new elements

Finding a drip pan that fit so that pots could sit level.

  • Customer: Ann B from Hueytown AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered the drip pan from ParSelect.com. Unplugged element and took out old pan. Placed new pan in and replaced element. For the first time in many years, the part fit.

Stove was not getting enough power.

  • Customer: Nathan from Wells ME
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

The 8" burner switch heated burner to high Temp

  • Customer: Randy from Ellenboro NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Went online looked up model no and found Part No. and ordered it couple of days It came in mail Cut power to oven took knob off two screws back panel. wired new switch like the old one replced thwe switch and two screws and panel connected the power tried new switch it worked great.

burner sparked and stopped working

  • Customer: Marvin from McAlpin FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
watch the vidio on your site very easy repair!i give you guy's 5 stars out of 5 !

Front and back burners not getting hot

  • Customer: Fred from De Leon TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the video supplied with the email on the parts order form. Biggest problem was pulling the range out from the wall, the repairs went without a hitch. The PartsSelect video was a great help showing the short cut to getting the new wires in by using the old wires as a pull wire.
All Instructions for the RA724K1WH
76-90 of 99