Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RA624F1WH

RA624F1WH Hotpoint Range - Overview

Get Parts and Repair Help for RA624F1WH

If you know the range repair part you need, you can browse the list of all parts on the RA624F1WH, or you can search by name or part description. You can also find your part by where it is located on the RA624F1WH by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for RA624F1WH parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the RA624F1WH

[Viewing 2 of 2]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.56

Drip Bowl - 6"

This six inch chrome drip bowl is intended for use with rolled terminal style plug in surface element units.

Order within the next 3 hrs and your part ships today!
$9.68

Drip Bowl - 8"

Sold individually. This part is located beneath the element and catches any spills.

Order within the next 3 hrs and your part ships today!
$48.30

Surface Burner Terminal Block Kit

This kit comes with the terminal block, mounting clip and wires.

Order within the next 3 hrs and your part ships today!
$36.62

Surface Burner - 8" - 2100W

Order within the next 3 hrs and your part ships today!
$35.25

Rolled Terminal Surface Unit - 6" - 1250W

Order within the next 3 hrs and your part ships today!
$1.82

DWR COVER CLIP

Order within the next 3 hrs and your part ships today!
$8.71

Indicator Light Kit

Order within the next 3 hrs and your part ships today!

LEVELING LEG

$8.96

OVEN DOOR GASKET

Order within the next 3 hrs and your part ships today!
$30.33

Burner Knob

Sold individually. This knob accepts a double-flat shaft.

Order within the next 3 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

There was no heat on the coils.

  • Customer: Shaohui from East Lansing, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 37 of 41 people found this instruction helpful
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe. read more

Surface burner coil did not work.

  • Customer: Gregory from Mont Belvieu, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 21 of 29 people found this instruction helpful
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet, but needed one. T... read more

Oven wouldn't heat well

  • Customer: LOIS from MINNEAPOLIS, MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
I removed power from the oven, then removed the 2 screws in the back of the oven that hold the element in place. I pulled the element out a little bit and disconnected the two wires. I connected the new element to the two wires, and screwed the two screws in the back. I then restored power and tested the oven - it worked great! read more