Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RA620F1WH > Instructions

RA620F1WH Hotpoint Range - Instructions

All installation instructions for RA620F1WH parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RA620F1WH
1-15 of 23
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

There was no heat on the coils.

  • Customer: Shaohui from East Lansing, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 37 of 41 people found this instruction helpful
I opened the lid, and found that the terminal blocks were burnt, the wires were melted. I ordered one set of terminal block to replace the burnt one, and it worked. Before I started, I shut off the electricity in the whole house to be safe.

Surface burner coil did not work.

  • Customer: Gregory from Mont Belvieu, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 21 of 29 people found this instruction helpful
TURN OFF ALL POWER TO KITCHEN. Took off all burner coils and plates below them. Lift hood. Locate part. Remove old part and replace with new part in same way as was previously installed. The wire that comes with the kit is actually too much wire, but just arrange it the best you can and leave it....no big deal. I didn't have a magnet, but needed one. The wire from burner coil to switch runs through a harness which is screwed on to the body of the oven (below the range). Be careful NOT to drop it behind oven when taking it out. I dropped it and took forever to get it. That turned a 20 minuate job into an hour and a half. Otherwise this is an easy job that anyone can do. Refrigerator compressor is next. Have fun.

Oven wouldn't heat well

  • Customer: LOIS from MINNEAPOLIS, MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
I removed power from the oven, then removed the 2 screws in the back of the oven that hold the element in place. I pulled the element out a little bit and disconnected the two wires. I connected the new element to the two wires, and screwed the two screws in the back. I then restored power and tested the oven - it worked great!

Oven wouldn't heat

  • Customer: steven from primm, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires

Large burner would not heat

  • Customer: Charles from Carthage, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 2 people found this instruction helpful
I ordered the wrong part to start with. (READ CAREFULLY!) I reordered the correct part and it was simple. I unpluged the old element, plugged in the new one replaced the drip pan and trim ring and we were back cooking.
Service was fast, lady I spoke with on the phone to exchange parts was knowegable and nice. Great people to deal with.

element burnt out because we had the food to close and it caught on fire

  • Customer: Claire from Hallandale Beach, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
removed two screws -took out -replaced and put 2 screws in----very easy

Burners would not lay flat

  • Customer: Alfred from Forest, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 9 people found this instruction helpful
Removed the burner elements, removed and disposed of old drip pans, cleaned the area, relaced with new drip pans and replaced the burner elements. Verified all burners were level - good as the day it was new!

Old unit was bent and didn't work properly

  • Customer: Christine from Danbury, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
I unplugged the old unit and plugged in the new one! It works.

coils with tips damaged

  • Customer: Jose from The Woodlands, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
it was very easy, a few seconds and new range for a cuople of years more!

burner broke apart under a pot

  • Customer: Mary from south bristol, ME
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Pulled out the burner. Just pulled and out it came. Looked you up online. Crawled around on the floor trying to find the model number. (This was the hardest part of the whole process.) Ordered the part; it came the very next day despite the fact that I didn't order special shipping. Unpacked the part, plugged it in. And it worked!!!!

FABULOUS service. Thank you so much.

Really, really grungy drip bowls

  • Customer: Donna from Brownfield, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Threw away old drip bowls, cleaned the top of the range, put on new bowls! So easy, a cave man could do it! All kidding aside, took knobs off and soaked them in hot soapy water for a while, cleaned part of stove behind knobs, cleaned under the burners, put it all back together, and while it doesn't look a new stove because it's at least 20 yrs old, looks 100% better. I think I can live with it for a while until I get brave enough to remodel my kitchen. Soooooo scary.....

Finish coming off of bowls

  • Customer: Robert from Ledyard, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Removed burner from each one. removed drip bowl. Inserted new bowl. Replaced burner. Excellent help from order people so I got the correct bowl was irreplacable.

metal "Y",shape metal long arm attached to burner came loose.holding the coil to burner

  • Customer: Audret K, from San Diego, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
just plugged in the two prings into burner into outlet. Very simple and quick.

The Heating Element's Contacts Were Burnout

  • Customer: Manuel from Quakertown, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
Quite simple, just plug-in the new one

Could not find the correct drip pan for my stove.

  • Customer: Kenneth from Oakford, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The drip bowls on my stove where getting rusty and I had a hard time getting the correct size for the 8 " burner. Wasted mony 3 times before finding it on partselect.
All Instructions for the RA620F1WH
1-15 of 23