Quick Question!

Have you ever purchased from PartSelect.com before?

Models > PYE4500AYQ

PYE4500AYQ Maytag Dryer - Overview

Get Parts and Repair Help for PYE4500AYQ

If you know the dryer repair part you need, you can browse the list of all parts on the PYE4500AYQ, or you can search by name or part description. You can also find your part by where it is located on the PYE4500AYQ by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for PYE4500AYQ parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.56

Multi Rib Belt - 92-1/4"

This multi rib belt is an important part in your dryer, it is what helps rotate the drum. The belt attaches to the drum, idler pulley, and motor pulley. As the armature of the moto...

$13.31

Lint Filter

This is an OEM lint filter for a dryer. This lint filter screen has two side guides on either of the screen. One measures 3/8 of an inch wide, while the other measures 5/8 of an inch wide. This part is white and is made of plastic. You may need to replace the filter if the plastic is broken or warped. Simply slide the lint filter out of the slot and slide the replacement filter in. The lint filter collects lint from drying clothes and prevents lint from building up in internal moving parts, specifically the heating coil. Neglecting to clean your lint filter is a fire hazard, be sure to clean it on a regular basis.

$14.78

Door Catch Kit

This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. ...

$3.02

Screw

This screw is sold individually.

$43.08

Blower Wheel

This wheel has a deep D-shaped shaft receptacle. The spring clamp is not included with this part.

$50.03

Rear Drum Support Roller Kit

The rear dryer drum roller functions by holding the drum in place while the drum rotates on support wheels during the drying spin/tumble cycle. Included in this rear drum support roller kit are four screws, one spacer, two washers, two retaining rings, two rear rollers, and two cylinder support shafts. The drum support roller kit may need to be replaced if the dryer is noisy or will not tumble. Important note: This kit has been updated by the genuine manufacturer to have one spacer that is the thickness of two spacers. Please search by model number to get these parts separately.

$5.81

Blower Wheel Clamp

This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and p...

$16.18

Rear Drum Support Roller

This rear drum support roller stabilizes the dryer drum and holds it in place during the drying cycle while the drum rotates on the support wheels. If your dryer is making loud squeaking or thumping noises, or the dryer will not tumble, there could be an issue with your rear drum support roller. If you can see that the roller is damaged, you should replace it right away. The repair is relatively easy, and takes between 15 minutes and 1 hour to complete. This drum support roller works with electric or gas clothes dryers, is sold individually, has an outside diameter of about three inches, and comes with a bearing.

$34.15

Motor Pulley

$18.18

Drum Felt Seal

The drum felt seal, used in dryers, allows the drum to smoothly glide with minimal friction. If any of the following symptoms occur with your dryer, replacing the felt seal can be a solution to your problem: makes noises, does not tumble, takes too long to dry, not enough heat, or no heat at all. First take off the front panel of the dryer and remove the drum. Next, unscrew the old drum support wheels by following the instructions from the manufacturer manual. To get the retaining clips on, place them in front of the wheel shaft and clamp down on the clip and shaft as you snap it in. This part can be used for both the front and rear in some models. Remember to unplug your dryer from the power source before beginning this project.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

lint filter broke

  • Customer: Jane from Grand Forks, ND
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 470 of 478 people found this instruction helpful
I pulled out the broken lint filter and put the new one back in, real easy. I am so happy with the prompt delivery I got from PartsSelect.com. I ordered on a Monday and and it was delivered on a Wednesday read more

broken lint filter

  • Customer: BRUCE from SAN MARCOS, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 137 of 210 people found this instruction helpful
First went and got a beer.
Looked at the dryer.
Drank my beer.
Went and got one more, due to long job.
Looked at dryer again.
Opened the door.
Had to get one more beer.
Removed filter.
Got one more cold one.
Put new filter in.
Got one more beer.
Closed door.
Finished! read more

broken tumbler belt

  • Customer: Michael from San Antonio, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 102 of 107 people found this instruction helpful
1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall when it loses suppor... read more