Models > PSS26SGPASS > Instructions

PSS26SGPASS General Electric Refrigerator - Instructions

All installation instructions for PSS26SGPASS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PSS26SGPASS
1,201-1,215 of 1,274
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ice was freezing at dispenser door and inside freezer

  • Customer: sanjay from trinity FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
It was amazing , i didn't know how to repair , i had. Insurance from choice home warranty but they say it is not covered , i was upset with them . But i get partselect .com . It is very easy, i tell my problem they tell what parts i need and also saw me video how to install it , i just did with a screw driver in 15 minutes . It was wonderful experience and a lot lot easy then what i thought. Thanks to partselect team and webside.

cover would not come off

  • Customer: dan from Cape san blas FL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the cover installed parts. Parts were very simple cover was a major problem. Instructions stated "simply remove cover by pushing on cover and clips will release" They dont and cover broke.

Flapper on ice dispenser wouldn't close after dispensing ice.

  • Customer: Thomas from Manassas VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
When I clicked on the part to see it's description the pop up window included a youtube video on how to install the part. The video was right on the mark. Very easy installation. Phillips screwdriver was the only tool needed. Repair performed in less than 15 minutes. I have used this site before and it has been extremely helpful in saving me money by doing the repairs myself instead of paying an arm and a leg for a repairman to do it.

Shoot for icemaker would freeze up. Pieces of ice would get stuck and than freeze together.Dispenser Door Flapper would not fully close anymore.

  • Customer: Karl from Miromar Lakes FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the vidio on your site, it was very helpful. Careful lifted the frame, unhooked the display panel. With phillip screwdriver took the 4 srews off, unhooked the PC board. Take out 2 srews for the Doorflapper. Loosen top screw for soliniod, take out 2 bottom srews and take out soliniod. Clean up area with paper-towel. Replace all new parts. And it works great again.

ice door would not open or when manually oppened would not close.

  • Customer: Gary R. from Ocala FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
exactly as described in your video.

Ice Door Not Closing, building up ice in refrigerator

  • Customer: David from Oviedo FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected power to unit. Using small Allen wrench unhooked 2 catches in electronic control panel. There are two holes underneath. Push up and pull out on panel as you release the catches. Remove wires. Remove 4 Phillips head screws in plastic panel, then remove panel. Solenoid has 3 screws. I replaced my screws being they were very rusty along with the solenoid. The spring on the door is easily replaced by removing two small screws on each side of the door hinge. There probably was nothing wrong with the old spring but for insurance replaced. Put the unit back together, no more ice buildup and clogging in ice chute through door. Likely saved $100 in labor repair bill by doing myself. Note: There is a few seconds time delay on the door closing. At first I thought I hadn't fixed the problem but then realized a delay in built into the system to avoid the door getting caught on any slow falling ice.

Flapper in door for ice dispenser would not close.

  • Customer: Clyde from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I repaired IAW the PartSelect video. Very easy. One thing that should be mentioned in the troubleshooting process, is to check the retention spring on the flapper. That spring could come off and also cause the flapper not to close.

A few small ice cubes in an empty try on return from vacation

  • Customer: Robert from Loudon TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Look at various pertenant DYI articles and videos on the internet. Replaced water filter with bypass plug. Checked water flow to icemaker water solenoid. Ran icemaker diagnostic test which failed. Ordered replacement. On receipt of replacement, began replacement work. To wit: Pulled fiidge from wall and unplugged. (Not necessary to shut water off.) Removed small freezer basket. Unloaded main freezer basket, removed it then removed the freezer door. (A screw on each side bolts the door rail of the chassis slide to the freezer chassis slide.) Loosened screws on rear, top of partition between icemaker and small freezer basket. Pushed up on partition front and popped out U-bar supporting partition bottom being carefull not to bend it. Removed same. Removed screws from partition and set aside. Removed grilled "thingy" between rear of icemaker and partition. Now have access to icemaker screws. Loosened the screws, pushed up and out and carefully let it hang by it's connector. Fiddled with the connector locking tabs and finally got it loose. Compared old and new icemaker. Have to keep the old water funnel. The new wiring harness was stiff and the connector had a different orientation. Twisted both the wiring harness and connector to align connector while the icemaker hung by it's cable being careful not to let the icemaer slip and fall to the bottom. After much fiddling, got the connector inserted and locked. Set icemaker over the two screws, pulled it down and tightend the screws. Put the old funnel into the new unit being very careful to get it right the first time. Put grilled "thingy and the partition and U-bar back in, put door back on, put the ice cube bin back, freezer drawers bac and reloaded the frozen food, plugged fridge in. Done! Time to replace icemaker was about 20 minutes and another 2 hours to do the rest ofthe work. Still required only a nutdriver and phillips.

Plastic part of icemaker broke

  • Customer: Robert from Glen Ellyn IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and then read the instructions. Emptied and cleaned freezer compartment. Removed old unit and removed part of old unit to be used in new installation. I then installed the new unit and turned the water back on. I let the unit produce over night and through the first batch of ice away. Because of the various regrigerators this ice maker was used I had a little confusion recognizing our model, but worked through this problem useing some common sense. All around I'm very satisfied with the results.

Ice maker leaking

  • Customer: Don from Horseshoe Bay TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Quite easy. Turn off water supply and turn off ice maker at switch inside freezer. Unscrew the old unit, separate the electrical connection, and pull it out. New unit comes with parts that do not fit my refrigerator, so visually examine the new and old units, reuse any needed parts from the old unit, such as plastic water ramp. Reconnect the electrical connector, and screw it back in. Turn water supply back on and then turn ice maker back on at switch inside freezer. Discard unused parts. Wait up to 24 hours for new ice cubes to be made.

Ice maker made no ice and no water from dispenser.

  • Customer: Lani from Lakeside CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...

No ice!

  • Customer: Jacob from Waggaman LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Literally took out one screw and a wiring harness. Removed the old plastic piece off of the old ice maker and put on the new one.Installed new ice maker with the one screw and plugged the wiring back in.DONE!

Ice maker not working

  • Customer: Derek from Baton Rouge LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Went well. Changed the Ice Maker and then the Water Valve. All good and it is making ice.

Ice maker was leaking

  • Customer: Robert from Pampa TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watched the video that showed how to disassemble the ice maker. Then went right in and replaced the part and turned it on. It immediately started filling up the ice tray. I still have not been able to find out why it does not make as fast as the original ice maker. The tempeature for the freezer is set pretty cold.

change of ice maker

  • Customer: Conti USA, Inc. from Fort Lauderdale FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
It was exactly as shown in your instruction video
All Instructions for the PSS26SGPASS
1,201-1,215 of 1,274