Models > PLRU1778ES0 > Instructions

PLRU1778ES0 Frigidaire Refrigerator - Instructions

All installation instructions for PLRU1778ES0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PLRU1778ES0
91-105 of 123
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator was in 3 feet of salt water.

  • Customer: Frank from Chalfont PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I am replacing rhe electrical parts that were wet. The motor and freon piping are sealed and uneffected by the flood.

Fan would not start occasionally

  • Customer: Mike from Satellite Beach FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I unscrewed the screws that held the old fan on, disconnected the wiring harness and removed the old fan. I pulled the blades off the motor and put it on the new fan. One thing of note, the screw holes on the new fan weren't threaded. I assume this is by design, so I used the screws to thread the holes before installing it in the freezer. Once I did this, the rest of the installation was easy, just screw it back in and connect the wiring harness.

Rattling Noise from behind frig

  • Customer: Michael from Rockford MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Initially, I traced the noise down to the evaporator motor area. I thought it was the fan blade so I ordered and changed it. Noise level better but still not good. Then I ivestigated problem area again. Removed the motor,discoverd that the motor shaft was loose /drifting which caused the "hummm" and uneven fan blade rotation. Orderd and installed new motor and all is good.

Broken shelf in refrigerator door

  • Customer: Scott A from Louisville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It was simply a matter of snapping in the replacement shelf.

Broken blade on fan.

  • Customer: Deborah from Ridge Spring SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Used needle nose pleirs to slide the old fan off.Then slide the new fan on the spindle.The video really made this easy!

Door shelf bracket broke

  • Customer: Cheryl from Fort Myers FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I read the model number on the inside of refrigerator label, ordered the part online from PartSelect. Part arrived in 24 hours. My daughter placed bracket onto fitting and repair was complete in less than 10 seconds.

I broke the Meat Pan while washing it

  • Customer: Barry from Allentown PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered the replacement part on-line. When I received the part, I realized it was the wrong part. I contacted PartSelect and worked with the service representative, Julie H. She was excellent!! She determined that I had used an incorrect model number, and then she directed me to where I could find the correct number. She gave me clear directions on how to return the incorrect piece, and then sent me a UPS label to cover the shipping costs. Julie H was at all times, professional, friendly and very helpful!! Regards, Barry Halper

Noisy fan

  • Customer: CRAIG from PRESCOTT VALLEY AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove the cover panel inside the freezer, remove and replace the fan motor (pull fan blades off old motor and push on the new one) and replace the cover.

Part that holds the meat pan broke.

  • Customer: Sheila from Sevierville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Wasn't hard after I got the right part. Both left and right are decribed on order page as 42 and of course I order the (right)wrong side. Had to reorder (left)and got the correct side. Since the left side disintergated, I decided to keep the right side and replace both sides. Replacing was pretty much a breeze. Recently had to order a door shelf also. Replaced it in less than a minute. Delivery on these parts were great. Here in a matter of two days. Thanks parts replacement guys.

Door shelf broke..

  • Customer: Andrew from Fairfield CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered the part....arrived in less than 2 days and 2 minutes later...the salad dressing was back in its designated spot!!!

missing door shelf bin

  • Customer: Michael from Lagrange IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
fit right in no problem

shattered bottom shelf (crisper shelf)

  • Customer: WENDY from MONTROSE CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simple drop-in. No tools. Less than one minute "repair" time. Worrying that the glass would break en route was for not; huge box with lots of peanuts and bubble wrap prevented any potential breakage. Very satisfied with price, shipment (including time), and overall "repair".

broken door bin

  • Customer: joseph from westlake OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Snap the old one out, snap the new one in.

broke fan blade while trying to remove dust.

  • Customer: Jack from Kiefer OK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Removed old fan motor and installed new one.Not much room for big hands back there.Flexible extensions valuable on this job.

Coils not Defrosting and stopped freezing

  • Customer: Joseph from Yulee FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Upluged power pulled freezer out from wall removed the two screws that holds the defrost timer unpluged defrost timer pluged new timer in mounted new timer back with the two screws pluged freezer back in and job was complete. Freezer working fine.
All Instructions for the PLRU1778ES0
91-105 of 123