Models > PLEF398CCD > Instructions

PLEF398CCD Frigidaire Range - Instructions

All installation instructions for PLEF398CCD parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PLEF398CCD
16-30 of 56
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Board malfunction: Burner will not shut off.

  • Customer: Arman from Bloomington IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 6 of 10 people found this instruction helpful
Shut off the circuit breaker. Unplug the power cord. Remove the back panel or have it lean open against the counter. The board is located in the bottom left hand corner. Remove the white color board connections by grabbing the sides and gently rocking them out. Leave all the wire connections on the right hand side in place for now. Remove the board screws. There are 4 white snap on board holders. Squeeze the middle of the holder to release using thin nose pliers. Your finger nail may work here as well. Once the board is loose (keep the wires attached) remove the screw spacers from the back of the board and attach them to the new one in the same place. They should easily snap off but will not easily snap on. Squeeze the tip to push them in. Snap the board in place in over the holders and secure the board with the screws. Do not over tight. Match the holes with the white board connections and slide then in place. The old board is still hanging on the side connected to the wires. From the top remove each wire by rocking it out and place it in the same location on the new board. Don’t push too hard it may bend the connection flap or break it. When all the connections are complete the old board is free. Replace the back panel. Plug the stove in. Get the breacker. Keep fingers crossed. And test the burners.

right front burner would not turn off

  • Customer: Ronald from Crescent City FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 7 people found this instruction helpful
pulled the top back cover off, removed knob on front burner control, nut and replaced-Thanks for the prompt service on the part

Change on e of the inside glass

  • Customer: Ronald from Ozone Park NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,

Lacking oven racks on used appliance

  • Customer: Katherine from Roanoke VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!

I forgot to remove something I had saved in the oven, planning to remove it before using the range.

  • Customer: Marilyn from Clearwater FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

oven door BROKEN GLASS

  • Customer: elizabeth from fall river MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 8 people found this instruction helpful
Remove two screws from bottom of inside oven door slide oven door up of hinges in side of door has 2 more screws when removing hold handle it does come off at very bottom of door remove all screws cover comes off remove new glass from package and place over brackets put oven door cover back on put screws back on slide back on bracket put last screws on

replacing oven racks

  • Customer: Lawrence from Elmira NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
The replacement racks were spot on and the service was outstanding. had the racks in 2 days. Happy Happy Joy Joy! :)

replacing the fan on a convection oven (fan was making a vibration noise)

  • Customer: John from Stevensville MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.

Crack in inner door glass

  • Customer: Robert from Richmond IN
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 4 people found this instruction helpful
Removed two screws that are attached to handle then removed four screws from bottom edge of oven door. I was then able to remove the outer door glass,this gave me access to the three inner glasses. After removing the retainer for the glass assembly,I was able to remove all three and replace the inner one.I reversed this proceedure to reassemble.

cracked knob, broken control

  • Customer: JOANNE from WANTAGH NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 9 people found this instruction helpful
screwed off and screwed on, couldn't have been easier. Part came much sooner than date given, and I am very satisfied. Thankyou Joanne Konecky

broken lens over oven light

  • Customer: Leslie from Warsaw VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 12 people found this instruction helpful
Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

Broken oven door glass

  • Customer: Joseph from Cranberry township PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed directions for replacement of the glass from the web. Replacement was simple and easy.

oven wouldn't work

  • Customer: Steve from Hiram OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pulled stove away from the wall and unplugged it. Removed probe and cut the wires because the connection clip on the new probe was different from the original. Leave the wires as long as possible because you will need the extra length to splice the clip from the old probe to the wires on the new one. Replaced probe and plugged the oven back in. Done.

Cracked inner oven door

  • Customer: Steve from Hollypond AL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed outer glass first ,then worked my way thru to inner glass..

plasitc switch broke off

  • Customer: joe from lake worth FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
6srcews on back top panel removed unplug switch pull out old /broken switch put noew on in put lockwasher and nut on new one then plug back in put panel back on and your good to go
All Instructions for the PLEF398CCD
16-30 of 56