Models > PLEC30S9ECC > Instructions

PLEC30S9ECC Frigidaire Cooktop - Instructions

All installation instructions for PLEC30S9ECC parts

These instructions have been submitted by other PartSelect customers and can help guide you through the cooktop repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PLEC30S9ECC
1-9 of 9
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cord was not tightened enough by delivery crew.

  • Customer: Timothy from Spring Valley AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 28 of 50 people found this instruction helpful
PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools needed are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

Burned element

  • Customer: Tom from Wallingford CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 25 of 47 people found this instruction helpful
Flip up top, remove wires and two screws. Replace in opposite way. Turn off power to stove first.

Element Burn out

  • Customer: Jesse from Forest VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 21 people found this instruction helpful
Self easy

PS Great service Super FAST.
Thanks Jesse

loud sqeaking when dryer was running

  • Customer: John from Swanville MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 5 of 24 people found this instruction helpful
replace back bearing kit and new belt. all good now, thank you parts select.

Control will not work - only clock blinks

  • Customer: Sue from Lampasas TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

burner wouldn't heat up

  • Customer: Stephen from Columbia SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I unplugged the stove. Then I lifted up the top of the stove to expose the burners. I unscrewed the necessary screws and plugs that attached the old burner to the stove. Then I simply put the new one back in it's place. The stove was one of those flat burner stoves, and I was a little concerned that I would be able to do it. The repair man wanted to charge me $150.00 for labor.

Failed cooktop control Knob

  • Customer: Ed from Gaston OR
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
1) Turned off breaker to stove. 2) Removed all 4 control knobs. 3) Removed the nut/washer on the failed knob. 4) The cooktop is so heavy that is it not mounted to the counter top. Removed the drawer under the cooktop and push the unit up and out. 5) Get help and carefully flip the cooktop upside down. 6) Using a Philips screw driver remove the 6-7 screws that hold the box cover in place over the controls. 7) The circuit board is held in place by 2 clips for the digital display. Pinch the clips together and lift the circuit board up. Note it is a very tight fit and I broke one of the clips. 8) Remove all wire connections and replace with new unit. 9) Snap the new unit in and put the nut/washer back on knob. It will be tight, but do not over tighten the nut. I did it hand tight and that was enough. 10) Screw the cover back on and carefully put the cooktop back in place (2 people). 11) Put the knobs back on and turn the breaker on. All is good.

burner would not heat up

  • Customer: MARGARET from MILFORD PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
simple, removed a few screw's, unplugged old burner, plugged in the new one. that was basically it. easy!

No Power to the Oven

  • Customer: Tony from Hartford CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
All Instructions for the PLEC30S9ECC
1-9 of 9