PLEB30M9ECD Frigidaire Microwave Oven Combo - Instructions

This is an OTR microwave oven, needs to be removed to diagnose problem. I did not diagnose problem properly, I searched online for possible causes, read that (99%)percent of the time the interlock switch was bad and replacement should solve my problem. It was also stated to be an easy fix,15- 45 minutes depending on ability. I ordered the relay switch. Took the oven down then removed outer shell. With my multimeter I began to test, fuses(2), interlock switches(3)and transformer. 3 interlock switches were ok, fuses were fine, and had power to the transformer, meter could not read output of transformer because of high voltage, (2300v). I'm down to magnetron (about a hundred bucks) or the touch pad/ circuit board. I have a countertop micro that I'm putting in place of the OTR. As far as Partselect, my item was shipped and delivered on time, instructions for changing that part was quite accurate. Would order from here again, just do my homework first.

0. Turn off breaker to oven
1 Remove two screws holding oven into enclosure.
2. Remove trim piece from bottom.
3. Open oven door, and engage part on hinge which keeps door from closing all the way. Now, door can be lifted and removed, set aside.
4. Slide oven out. This is very heavy, and it's best to have two people as well as something slightly lower than the oven to put it on, I used a chair.
5. Remove microwave trim, 4 screws.
6. Remove baffle which protects microwave power cord.
7. Loosen 4 screws from bottom of microwave. I used a Screwdriver bit with a pliers, as there isn't much room. Slide microwave forward or back, and microwave can be lifted from oven.
8. Remove 4 screws on side, 2 security Star screws on bottom of back, and 3 regular screws on back.
9. Remove top heat shield, and top/sides cover. Danger, do not plug in microwave with top/side cover missing. Also, capacitor on right/back may hold dangerous voltages, short the terminals using well-insulated tool. There is a bleed resistor which is supposed to do this, but you can never be too careful.
10. Open microwave drawer. Unscrew the front control panel from the inside. Remove plastic part the door open button usually moves, the part needs to be pulled to the left side to be removed. Take a picture of the wires attached to the switches on the latch plate, so you put them back correctly.
11. Remove wire connectors from switches. These connectors have a retaining feature, if you push the retaining feature, it doesn't take too much force to remove it. There are 6 wires. Remove the latch plate, there may be a screw or two.
12. Take note of which switches are normally own and normally closed. They have to go back the same way. I mainly took out the latch plate because the switches stopped working, a couple had welded themselves together internally. But, I had to replace the latch plate because I improperly removed the switches and broke the plate. The switches are held in place by a pin through the switch, a couple of static parts from the latch plate, and a tab which sticks up from the bottom of the latch plate. The pin is very fragile. Depress the tan from the bottom of the latch plate, and the switch should rotate on the pin. Do not release the tab until the such has rotated past it. Now, you can lift the switch.
13. Reverse all of these steps with the new patch plate to put everything back together. You might want to test the microwave before reattaching it to the oven.
14. To put the oven back into the cavity, it's best to lean the back edge over the bottom of the cavity, then lift the oven from the front and slide it in.

remove oven door, disassemble front of glass top range then basically
it was just plug and play then reassemble be careful oven door is heavy

Tool old elentment out, put new element in

1. Loosened 2 sensor mounting screws and removed them. 2. Tripped range circuit breaker to off. 3. Pulled out the range but left gas connected. 4. Loosened the 4 screws on RH side of the top back panel and carefully pried that side of the panel open. 5. Using fingers, threaded the sensor's wiring harness through insulation and into the oven. 6. Unplugged old probe. 7. plugged in new probe. 8. tugged wiring harness back through insulation behind the oven. 9. Using 2 screws removed in 1 above, mounted new sensor. 10. Repositioned top back panel and fastened it in place. 11. Shoved range back in. 12. Tripped range circuit breaker to on. 13. Reset clock. 14. Set oven to 450 for test tun. 15.

replaced it

Removed unit from above stove removed outer housing, interior shield and tested the 4 door relays. One was not working. Replaced parts and re installed unit over stove.

Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan

Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.

I purchased one relay switch (there are three) took one out one by one and replced it with the new one and tested it each time until it worked. Super easy and saved me hundreds of dollars by doing this myself.

Much like the other post: 1. Removw vent case on top (3 screws) 2. Remove cover with control buttons (1 screw). 3. Removed bottom relay switch and replaced. Tight working space so be patient. Took 15 minutes Needle nose pliers used to crimp connector onto switch

Took 3 panels off to get to the electric block. Replaced electrical block and put it back together. Still no change.

I managed to move the auger far enough to allow me to insert the cup-drive and then realign the auger with the new cup-drive. I also have had one to break very shortly after installing it. This is my second part to replace and this one went really smooth, since I understood that the initial parts installation instructions did not apply on my ice maker.

Easy as 1-2-3

Really a no brainer, but I do have to say that PartSelect customer service is excellent. My part was located and on it's way within a day and arrived a couple of days later.