Models > PLD2855RFC1 > Instructions

PLD2855RFC1 Frigidaire Dishwasher - Instructions

All installation instructions for PLD2855RFC1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PLD2855RFC1
361-375 of 404
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The upper spray arm had fallen off.

  • Customer: Cathy from Brandon FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered a new upper spray arm. Detached the old arm holder using a rag because it was on there very tightly. I had to use a pair of scissors to hold the connector to keep it from sliding up while screwing on the new piece. It was super easy and the video was right on. After finding something to hold the connector tube comin out of dishwasher top it took about 30 seconds. Super easy!

need drain house

  • Customer: Wilburn from Cumming GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Very helpful and was amazed how quickly it was delivered. Very pleased.

mouse made hole in both drain hoses

  • Customer: james from tracy city TN
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
pulled machine out removed old put on new, which were a perfect fit. and were received remarkably fast.

Upper wash arm not working. Not getting proper water fill level.

  • Customer: jens from west lafayette IN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Disconnected washer & replaced water inlet valve & supply hose. Releveled washer.

Dispenser would not dispense.

  • Customer: Johnie from Aztec NM
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed 4 screws on door cover, 6 screws on dispenser 4 wires and reinstalled new one. Done less than 20 minutes.

dishwasher door opens to floor

  • Customer: MAURICE from SAUTEE NACOOCHEE GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
just removed the screws holding the dishwasher in and pulled it out about 6 inches and attached the new springs one on each side. very easy and simple. no tools needed to attach new springs. be sure to cut off power to dishwasher before attempting this.

Lower spray arms were curving upward because of drying heater element, catching on lower rack, and wasn't turning or cleaning anything.

  • Customer: David from Westfield MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled the bent spray arm straight out, snapped the new arm back on. Took 10 seconds, and no tools needed. Wish all repairs were that easy....

No water

  • Customer: Bret R. from Angola IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Tested main water supply first and it checked out, next thing was the valve got a new one took old one off, flushed the line a few times to get dirty deposited water out, stuck the new inlet valve on and ran the dish washer and it worked, really a pretty easy thing to do anybody can do it and it will save you a couple hundred bucks in the repair mans labor and his cost for parts, deffinetly a must do yourself job. Got my part in two days from when I ordered it.

Water was leaking out of the pump

  • Customer: Travis from kunkletown PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed dishwasher from under counter and turn it on briefly and found that the pump was leaking and not from the o rings that seal it ordered a new pump and it took about 3 min to put the pump in and the rest of the time was reinstalling it under the counter.

DOOR LEAKING

  • Customer: willis w from broomes island MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
ALL I HAVE TO SAY IS PAETS SELECT IS THE BEST COMPANY I HAVE DELT WITH IN THE LAST 20 YEARS

the tub was leaking at the right front corner

  • Customer: Raymond from El Paso TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just pushed it into the crevice with my thumb

Replaced Cover and Stem Assembly Frigidaire DW

  • Customer: jamie from Fairfield CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Your site is awesome.. not only show the parts but a video for the repair as well.. very smart site.. I will be back.. The repair was quick and easy. thank you..

Lower sprayer arm wouldn't stay on

  • Customer: Charles from Del Valle TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took lower tray assy. out and took 3 screws out of cover and stem assy. and replaced old with new. Took me about 15 min. Part was perfect match so job was a piece of cake.

Door leaked at the bottom corners

  • Customer: Jason from Ferndale WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pull the old door seal down and out starting at one end. Push the new seal back in, noting the small notch location. Done!

upper spray arm came off during wash cycle

  • Customer: Jean M from Beaverton OR
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We ordered a replacement spray arm, and thought we had received the wrong part, because it would not screw onto the tubing that come down from the top of the dishwasher. Called and did some troubleshooting with a customer service rep and ordered two more parts (gasket and grommet) that we thought might be necessary. They did not help. Called back in frustration and finally the person on the other end found a comment in someone else's instructions about holding the delivery tube still with a putty knife while screwing on the spray arm assembly. We followed that advice, and got the spray arm on. Actual time to put the new part on once we figured out the problem: less than 10 minutes. Time spent troubleshooting: over 2 hours.
All Instructions for the PLD2855RFC1
361-375 of 404