Models > PHT219HSM3

PHT219HSM3 Frigidaire Refrigerator - Overview

Get Parts and Repair Help for PHT219HSM3

If you know the refrigerator repair part you need, you can browse the list of all parts on the PHT219HSM3, or you can search by name or part description. You can also find your part by where it is located on the PHT219HSM3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for PHT219HSM3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$22.11

Refrigerator Door Shelf Bin

Sold individually.

$19.21

Defrost Timer - 60Hz 120V

This defrost timer will cycle for thirty minutes after every eight hours of run time.

$22.47

Meat Drawer Rail - Right Side

As you look into the fridge, this drawer support track is located on the right hand side.

$56.46

Fresh Food Door Gasket

This white fresh food door gasket is used to seal the refrigerator door when closed to keep the cool air inside and the room air outside.

$19.35

Run Capacitor

This part is attached to the compressor. It helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

$14.79

Defrost Thermostat

The thermostat senses that the heat near the cooling coils has reached the desired temperature.

$24.68

Meat Drawer Rail - Left Side

This drawer rail supports the left hand side of the sliding drawer. The mounting screws are sold separately.

$21.76

Water Inlet Valve

$45.61

Evaporator Fan Motor Kit

This kit includes the motor, clips and terminal connectors. This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. Thes...

$116.08

ICE MAKER

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Refrigerator door gasket torn

  • Customer: Matthew from Washington DC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 88 of 92 people found this instruction helpful
No instructions included, so it took a little bit of staring at the new part to figure out how it works. The barbed ridge on the gasket fits into a slot on the door. The flat face of the gasket has an internal magnetic strip that helps keep the seal tight against the steel face of the refrigerator. Installation requires no tools. This is the basic process:read more

evaporator coil kept freezing up, refridgerator warm.

  • Customer: Greg from Hanover Township PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 84 of 94 people found this instruction helpful
This was the second part I tried. The defrost timer was first, but that did not fix it. To do this I had to remove the ice maker and the back plate of the freezer. Then I defrosted the coil and cut the wires. stripped them back and installed the new thermostat. re-assembled and tested. has been working great ever since. read more

bottom of fridg. would not get cool. Temp was 50-60degrees. The freezer compartment worked so I knew it was not the compressor.

  • Customer: Larry from Carthage NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 54 of 62 people found this instruction helpful
I removed the fan housing in the freezer section by removing all the screws. (7) There are two screws behind the vents. I did not have an ice maker to contend with so this was very easy. There is only two wires to disconnect....the ground wire and the electricity supply. Then you remove the unit from the back of the housing cover by removing two screws. Th... read more