Models > PHS68EJSB0 > Instructions

PHS68EJSB0 Frigidaire Refrigerator - Instructions

All installation instructions for PHS68EJSB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PHS68EJSB0
436-450 of 595
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken shelf

  • Customer: James from Warren MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Out of the box and slipped right in on the door. Part was here in 3 days. Excellent service.

broken door shelve

  • Customer: Laurel from Pierceton IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
snap drawer in place

I broke the glass shelve insert

  • Customer: Irene from Mount Prospect IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply ordered the replacement, no instructions required.

Broken bottom door tray

  • Customer: John from Eatonton GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered one day, got it the next, popped right in place. Identical part, super service.

broken bottom door bin

  • Customer: jon from lamoine ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
installed new door bin

Broken Water Dispenser Actuator

  • Customer: Anne from sun City AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
watched youtube video on this repair that helped a lot.Remove tray and front plate - gently pull out ribbon wire that connects to front plate.I warn you not to screw back plastic pieces too tight - I broke some plastic that I had to glue back. I did job without removing water tube from mechanism - it pulled out just enough to reach screws holding actuator - also it is a bit difficult to push back ribbon wire that connects into front plate. test before screwing mechanism back -ribbon wire must be reattached to test

worn rail on righy side

  • Customer: Gilbert from Endio CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed meat drawer ,,,titled on it;s side , used philip screw drivingto lossen screw ,,removed worn rail and replaced it with new one in less then a minute,,, very easy and cool ,,,

Broken crisper cover support

  • Customer: Thomas from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Received the parts promptly and did the repair just as the video showed. All went well and had the repair completed in 10 minutes. For me that was remarkable because I have two left hands! Would highly recommend partselect.com

freezer would not freeze longer than one day. after ten years without problem

  • Customer: ronald from deering NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
pulled out freezer, went to floor,reached in next to compressor pulled off clip just like on the video.Pulled off old capacitator took off wire leads.Installed new one. Freezer runs great.Loaded it up with beef pork and venison. No problems.

Overdue replacement

  • Customer: Carl from Melbourne FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Everything went according to plans and as expected. It could not have gone any easier. Customer service was outstanding! I will certainly use your service again.

The drive blade was worn and wouldn't turn the drum

  • Customer: RORY from OAK HARBOR OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
First off make sure you have a good quality Phillips screw driver. When the blade is worn out you can disassemble the ice maker with out removing the front. But to reassemble the front cover must be removed. Do yourself a favor and buy the drum and nut also. I am a mechanic by trade so the tools and repair was really easy. Be careful of the ice crusher BLADES they are very sharp. If your not mechanically inclined take pictures before disassembly, that will help you greatly. Hope this helps someone. Thanks Rory

Water leaking from dispenser

  • Customer: Gary from San Angelo TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Used a nut driver to remove the small panal from the back of the refrigerator. Removed the two screws holding the valve in place. Unscrewed the water lines from the old valve and cut the ends off of them. Push the water lines back into the new valve. Unpluged the wiring from the old valve and installed them in the new valve. reinstalled the new valve and put the cover back on. Tested system for proper operation.

No power to front panel for ice, water, and light.

  • Customer: Derrick from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the ribbon from circuit board in door to the circuit board which controls the water and ice dispenser and back light. Unplug the refrigerator before any repair is attempted. You can short the boards when replacing the cable. Remove the front plate where the buttons are. Be careful, it slides up then out. once you remove the outer panel, you will see the ribbon which attaches to the front panel to the circuit board in the door (of course freezer side). on the plate you just removed, there is a white cover plate secured with four small philip head screws. Don't try to replace the ribbon without removing this cover. If you do, you run the risk of breaking the the ribbon and then you'll have to order another one. Make sure you note which way the cable is inserted. Insert the cable in both slots on the door and panel. Replace the screws and front panel.

Fit great

  • Customer: Elizabeth from Havertown PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Slid bin into door

ice dispenser and ribbon cable broke

  • Customer: Angel from Miami FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
i dissasamble the water & ice dispenser and substitued the ribbon cable for the new one.
All Instructions for the PHS68EJSB0
436-450 of 595