Models > PHS68EJSB0 > Instructions

PHS68EJSB0 Frigidaire Refrigerator - Instructions

All installation instructions for PHS68EJSB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PHS68EJSB0
1-15 of 566
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

yearly maintenance

  • Customer: Antonio from Folsom CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 491 of 496 people found this instruction helpful
swap filter

Tab on bottom door bin broke off

  • Customer: Mark from Redlands CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 470 of 473 people found this instruction helpful
Replaced bottom door bin being careful not to put stress on the tabs to fit into molded area in door.

freezer shelf broke

  • Customer: MONICA from LANCASTER CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 459 of 462 people found this instruction helpful
Easy slide it back in place

Replaced door shelve

  • Customer: TERRI from STOCKTON MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 456 of 537 people found this instruction helpful
We live in rural SW Missouri, so I am very dependent on the internet. I found PartSelect on a Google search and simply inputted the modle number and serial number for the refrigerator and there it was. I was able to order the right part the first time and repair the refrigerator myself! No serviceman needed here!

Bottom Door Bin had cracked

  • Customer: Bogdan from Lehi UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 446 of 534 people found this instruction helpful
Not much of a repair. Just swapped the old bin with the new one.

easily found the part I was looking for

  • Customer: ARLENA from MANASSAS PARK VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 360 of 581 people found this instruction helpful
The website was easy to navigate. Loved the schematic drawings of the appliance, it made it easy to find the part you are looking for without the guesswork (part names are sometimes not intuitive). My parts arrived promptly, the price was competitive, everything fit beautifly as expected. Would recommend this merchant, will shop there again. THANKS !

water leaking out of refrigerator

  • Customer: Jose from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench(Adjustable)
  • 168 of 203 people found this instruction helpful
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.

Support studs were broken

  • Customer: Peter from Amherst NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 146 of 151 people found this instruction helpful
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers.

Took bin out to wash and it broke getting it out

  • Customer: Richelle from New Berlin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 150 of 229 people found this instruction helpful
No tools needed. Just had to slide the bin into place. HOWEVER, the bin has a jig-jagged style plastic groves on each side that need to be slide carefully into place. I couldn't get the orginal bin out in order to wash it. It looked easy - just slide it up and out of place, but when I did that the back, inter-locking pieces cracked off. I believe this is a terrible design and the bin should be replaced at the manufactures cost! The other bin slide in there with some elbow-grease. Good Luck!

Running but not cooling off and frost in the back of the freezer

  • Customer: Leo from Bentonville AR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 123 of 157 people found this instruction helpful
Unplugged the refrigerator. Removed the 4 hex head screws on the lower back panel at the back of the freezer. Used a blow dryer to defrost the pipes and area surrounding the thermostat. Unplug the connection from the back of the freezer, unplug the 2 wires, one that goes to the heater, one that comes from power. Unclip the thermostat from the pipe and note which pipe you unclipped it from. Cut the wires on the old thermostat midway between the plugs and the sensor. Using the supplied butt connectors, strip the wire ends on color matched wires (should be a dark blue or black) and crimp them together. Repeat with the other wire. Discard the white shrink wrapping. I wasn't able to get it small enough with a hair dryer or lighter. Plug the thermostat back into it's respective plugs. Clip the thermostat back onto the pipe you removed it from. Replace the back panel with the four screws. Ensure the bottom of the panel is set inside of the drip tray. Replace any shelving you removed. Plug the refrigerator back into the wall. Your done!

icemaker stopped making ice

  • Customer: David from New Bern NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 104 of 123 people found this instruction helpful
Even though my wife said that our icemaker broke, there was actually nothing wrong with it. It was the valve that let water flow in during the 'harvest' cycle.
A real easy way to test the icemaker without voltage and current measurements, is to fill the tray by hand with a little cup of water; wait till the water freezes and see if the maker dumped the ice into the bin.

water leaking(pouring) from the filter into the refrigerator

  • Customer: Michele from Red Oak TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 82 of 91 people found this instruction helpful
Pushed the button on the filter in the fridge, the cartridge popped out and in with the new. That simple. Prior to replacement the water was leaking, although it was still producing water and ice through the door. When the filter was out, no leaks, but no water and ice! Just needed a new filter.

Broken door bin

  • Customer: Elizabeth from San Diego CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 81 of 146 people found this instruction helpful
The repair was not my worry, but ordering the correct part. I was so pleased with this web site and the quick delivery of the part that I ordered. I easily found the bin I needed for my refrigerator and had the part at my doorstep with two days. I am extremely happy with this site.

bottom of fridg. would not get cool. Temp was 50-60degrees. The freezer compartment worked so I knew it was not the compressor.

  • Customer: Larry from Carthage NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 51 of 58 people found this instruction helpful
I removed the fan housing in the freezer section by removing all the screws. (7) There are two screws behind the vents. I did not have an ice maker to contend with so this was very easy. There is only two wires to disconnect....the ground wire and the electricity supply. Then you remove the unit from the back of the housing cover by removing two screws. Then the motor is removed from it's housing by removing 2 more screws. 1...2...3 and you're ready to reverse the procedure. I am not mechanically inclined and this was easy. Saved myself perhaps $120.00. Repair folks wanted mininum of $60.00 just to come out. Part and shipping cost me 33 bucks.OH, DON'T FORGET TO UNPLUG THE FRIDGE. :>)

Refrigerator would sometimes freeze everything

  • Customer: donna from brandon FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 46 of 55 people found this instruction helpful
we researched the internet with our symptoms and most sites said it was the thermostat. At $800+ for a new refrigerater, we decided to order the thermostat. Found schematics on the net, the thermostat was located in teh freezer compartment . Unplugged, removed food from freezer, removed the bottom shelf in freezer, and the back panel It was EASY to find. Cut 2 wires, replaced with new thermostat. DONE! The new thermostat came with new connecters.
All Instructions for the PHS68EJSB0
1-15 of 566