Models > PFS22SISBSS > Instructions

PFS22SISBSS General Electric Refrigerator - Instructions

All installation instructions for PFS22SISBSS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PFS22SISBSS
256-270 of 357
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

freezer and refrigerator wasn't cold

  • Customer: Laura from Brentwood MD
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Replaced all the sensors in both the feezer and refrigerator.Even though it colder now it still is not cold enough.Freezer won't freeze items but is cold and refrigerator still not real cold

Freezer and frig both warm and compressor would not run

  • Customer: joe from decatur GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I replaced the thermostat, temperature sensor, and the run capacitor...refrigerator still not cooling. I checked the start relay and measured the input terminals on the compressor for the correct resistance...everything measured correctly. In a last ditch effort before calling for service, I pulled the main board, inspected it and saw the problem right away. One leg on the compression capacitor had desoldered itself. Got out my soldering iron and applied a good amount of solder to that point. Put everything back together and turn it on...problem fixed. The compressor kicked on right away and started cooling the refrigerator.

Refrigerator and freezer stopped working, only inside lights on

  • Customer: Marinez from Bridgeport CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Really easy to change the board..I did spend more time trying to figure it out how to plug the ground wire, as the new board had different wires to ground. What i did was i switch the ground wires from the old board and put them in the new board. Problem solved, refrigerator and freezer running like new.

Tempeature in fresh food section was unstable and dropped below 32F frequently. Service technician had previously replaced the two temperature sensors but this did not remedy the problem. I decided to replace the main control board and this seems to have have resolved the problem.

  • Customer: James from Crestwood KY
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed the cover plate to gain access to the main control board. Disconnect the electrical connectiosn ad repalce the board. re-connect the electrical connections.

would not run no lights on panel control

  • Customer: Ricky from Panther WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
real easy unplugged fridge took back small plate off marked and unplugged wiring plugs squeeze the four tabs still was tight coming off be careful or might break a tab i didnt but tight as it was knew it might happen so was very careful installed other board and put plate back plugged up worked prefect saved alot on repair bill for sure

Freeze and refrigerator sides at times were warmer than normal. Would not dispense water or ice threw door dispenser, also could hear a clicking noise every so often the last about 10 minutes at a time. I think the clicking would start on the main board when it went into the defrost mode. Defrost mo

  • Customer: Winston from Ford VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
UNPLUGGED the Refrigerator.Removed two screw from the panel on the (outside) back, took panel off, removed the wire harnesses, carefully removed old board off of the plastic pins, pushed new board on the pins, put wire harnessed back on in their proper places, put cover back on. Everything that was not working, was working now. Took less than 15 mins..

The water and ice dispenser suddenly stopped working. The light in the dispenser would dim whenever we tried to get water or ice.

  • Customer: BILL from N OLMSTED OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I pulled the power cord, removed the screws and the cover. After removing the screws from the main control board I unplugged all of the connections from the bad board and plugged them into the new board in the same order. An easy change and a real moneysaver!

replace control panel

  • Customer: Mary from New Orleans LA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was simple really. Merely a replacement part. After disconnecting the ribbon cables and removing old panel all that was left was to reconnect all 3 ribbon cables and the ground and put the cover back on. Simple even for a girl :-)

Water/Ice dispenser stopped working and clicking noise from freezer

  • Customer: Mark from Liberty MO
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
This is a very easy repair. The hardest part was pushing the fridge in and out and having to clean back there!!. Before starting anything, I unplugged the fridge from the wall outlet. I removed 4 nut-drive screws holding the circuit board cover to the back of the fridge. Once the circuit board was exposed, I first compared the current board with the new one to make sure the connections were the same. I did have to use the already existing ground wire (green wire) for the circuit board as the new one provided with the new board had the wrong connectors. I then marked each wire harness from left to right, top to bottom, so I knew what order they were to be reconnected. I then disconnected the 5 wiring harnesses. The hardest part of the repair was removing the board itself. There are 4 plastic connectors holding the board in place. I tried to squeeze them with the pliers, but the board would not come off. I then watched the online video and realized I was squeezing the connectors wrong. After changing how I was squeezing the connectors, the board came out very easily. It was very easy then to snap the new board into place, reconnect the wires, and plug in the fridge. I did test everything before replacing the cover just in case I needed to reconnect something, etc. All in all, this repair took maybe 30 minutes, but that included time to gather the tools, pull out the fridge, clean behind the fridge, replace the board, test the system, and push the fridge back into place. Very Easy

Condensor Fan Motor not working, unit getting hot

  • Customer: Ron from Metairie LA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Noticed the interior wall hot to the touch when opening cooler or freezer door (side by side). pulled lower panel off in rear of unit and noticed fan motor not working. Ordered new fan motor, installed , still did not work. used volt meter to test for power from main control panel to motor. No power present. Ordered main control panel board and installed. Fixed problem. It ran excellant for about an hour and then the control panel shorted out the main control panel and motor that had just been purchased. Both were replaced at no additional charge by Customer Service. Second installation was a success. Sometimes bad things happen to an already bad situation. It's nice to have the understanding, support and service offered by Parts Select. I guess that's why I use them every time there is a problem. G E is easy to repair as long as you use patience and determination.

change of ice maker

  • Customer: Conti USA, Inc. from Fort Lauderdale FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
It was exactly as shown in your instruction video

My fridge was colder than my freezer

  • Customer: Marco from Fallbrook CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I can't tell you how luck I feel after finding your website I ordered the temperature sensor after watching one of your videos on-line and the repair went just as on the video. I pulled the "bad" sensor out, and replaced it with the new one. Keep in mind that this is the first time I ever touch an appliance, needless to say I'm feeling pretty good about that! All in all it took me about 20 minutes to complete my repair and it now has been about 4 days and the refrigerator is working like new again!

Compressor not coming on, not cooling.

  • Customer: Kevin from Morris IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Main Control Board not grounding compressor circuit. Jumped compressor to mak sure it would run. Compressor ran fine control board malfunctioning. Diagnosis was the hard part. Installing the board was very easy.

refrigerator and freezer were not cold enough nor would they stay a constant temperature

  • Customer: Dan from Meridian ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I moved the refrigerator away from the wall, removed the back cover with a 5/16 nut driver, i removed the plugs from the board carefully using neadle nose pliers if needed, then i used the pliers to release the plastic tabs holding the board( 4) installed the new board reversing this process.

freezer warming

  • Customer: Terrance from Excelsior AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
pulled the plug and removed screws took out old board and put in the new
All Instructions for the PFS22SISBSS
256-270 of 357