Models > PFS22SISBSS > Instructions

PFS22SISBSS General Electric Refrigerator - Instructions

All installation instructions for PFS22SISBSS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PFS22SISBSS
241-255 of 381
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

not cooling no display, ice maker water dispenser not working

  • Customer: Owen from Conyers GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replace main board.

Was not making ice

  • Customer: Colleen from Yorba linda CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took old part out , put new part in. Was so easy thought we did it wrong. Ice maker working great, have lots of ice now. Thank you. Colleen

coil frosting up and refridgerator section was not cooling

  • Customer: Vernon from Harmony NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
took out shelves and removed the back plate my removing 2 screws with a nutdriver.removed the old defrost timer and defrost heater which was really easy.then installed the new ones.the video i watched on the website was really helpfull.

refrige ws too cold

  • Customer: Jeffrey from Saint Charles IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
as per video

Icemaker leaking water

  • Customer: Allen from Santa Fe NM
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I had to defrost the freezer to free the icemaker. After that the installation was plug and play with two small exceptions: 1) I had to file down the width of the left hand tine of the old stripper so that it would fit the new icemaker, and 2) the motor housing of the new icemaker was slightly wider than the old one. It fit, but just barely. But I'm back in the ice again, no dripping water, all is good.

iCE MAKER LEAKING WATER

  • Customer: Roy H from Leesburg VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Followed the video demo and would have been done sooner but for limited work space- narrow freezer compartment and the release tabs on the electrical plug. First home repair that the air was not blue and got done in under time allocated.

Unit was shutting down the ice & water despencer would quit. in side lights still on compressor off

  • Customer: LYNN from FERRIDAY LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Replace main control board .Problem solved.

frige too cold

  • Customer: John from Island Lake IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.

Ice maker failed. Easy to diagnose cooling coil was very hot

  • Customer: Al from Coto de Caza CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Seemed simple and intuitive B U T the water tube receiver fooled me. Seemed to be on backwards. So, like my wife suggested, I D I D then read the installation instructions. Yeah! It's amazing what you can do when you just RTI. :-0

missing door bins

  • Customer: kathleen b from philadelphia PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very easy installation and speedy parts delivery. thank you

Freezer defrosting; Temp Controls inoperable; Clicking sounds; lights on. Unplugging and then plugging back in would be a temporary fix, then it would revert to defrosting. Ice and water dispensers inoperable.

  • Customer: Carol from Shepherdstown WV
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Replacing the main control board was not difficult. When I received the order confirmation from partselect.com they included a link to their repairman video for the part replacement. Unplug; unscrew the panel; unplug the wired connections from the old control board; do use pliers to squeeze the corner clips that hold the board in place and remove old board. Slide new board over the clips; plug in all the connectors (they each have different number of pins so you can't confuse them); replace the back cover and plug the refrigerator back in. Very quiet now; temperature controls work; freezer works and as an added bonus, the ice and water dispenser is also back in operation. I had thought it was a separate issue, but lo and behold, replacing the main control board fixed everything. Thank you partselect!

Ice Maker stopped making ice cubes

  • Customer: Paul W from Clarksville TN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Freezer is located on the bottom. To acess the ice maker, entire contents of the freezer were removed. The power and water were shut off at the refrigerator. The shelves in the freezer were removed; the freezer door was removed;the shelve partitons/slides were removed. Sounds complicated, but the ice maker is located on the left side of the freezer and would be impossible to unscrew, remove, disconnect and install by touchy/feely method. Total time from start to finish was about 45min. Water filter: twist out twist in.

Refridgerator not cooling, freezer frosting over

  • Customer: Bill from Warrenton VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First, I had to remove the freezer drawer front. This is 8 large phillips head screws. then remove the plastic cover over the drawer slides. to do this, remove the white center screw from the slide near where it attaches to the drawer front. then the plastic cover will slide off pushing to the rear of the slide. take off the slides from the freezer walls by removing the phillips screws and pulling them towards you. They have tabs/slots in the rear. remove the center tray support and support bars, too. the icemaker has to come out, that is just 2 phillips screws but you also have to disconnect the electrical connector. just squeeze the locking wings and rock/pull. a screw in the top center of the back panel comes out. Lift and pull the back panel out. The evaporator coil appears. The thermocouple is attached to the coil in the upper right. Cut that one's wires and take it out. Just cut back about an inch from the back of the thermocouple, there is not much slack. Seperate and strip the wires back about 3/8 inch. Do the same for the new thermocouple. I twisted the wires together and used a solder sleeve to join the wires. The sleeve is just a little plastic tube that has a ring of solder in it that melts with heat gun heat. You can join the wires using butt connectors or whatever method appeals to you. I just wound the extra wire and put a cable tie around it, there is plenty of hiding space in that area. Make sure the new thermocouple is contacting the coil firmly.At this point, for a test, I left everything apart, propped the drawer against the opening and plugged the fridge in. Note that the evaporator fan will not start spinning immediately! It will just sit there making little bumps like it wants to go. The temp in the coil has to get settled before the electronics in the refridge will tell the fan to spin. It takes maybe 20 minutes. Reassemble. Fridge and freezer work great. It does take several hours for all to get cold again.

Would not cool.

  • Customer: Patricia from garden grove CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced board, easy to diagnose and repair.

Refrigerator stopped cooling

  • Customer: Mark from Colfax CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I watched the video that was provided by PartSelect. The process could not have been more straight-forward. After unplugging the fridge from the wall outlet, i unscrewed the 9 or so screws that attached the plate covering the circuit board, I carefully unplugged each of the wiring plugs that were attached to the circuit board, except for the plug providing power to the board. That one I was unable to unplug while the board was still attached to fridge. I then used a pair of needle-nosed pliers to release the 4 plastic clips that held the circuit board in place and removed the unit from its housing. I was then able to unplug the one remaining wiring plug. The new board had a slightly different design, so attaching the power to the board was easily done after mounting the new board onto the plastic clips. The entire process took me less than 5 minutes. I plugged the fridge back into the wall outlet and my refrigerator came back to life! Thank you PartSelect for helping to make the task so simple and straight-forward!
All Instructions for the PFS22SISBSS
241-255 of 381