Models > PFS22SISBSS > Instructions

PFS22SISBSS General Electric Refrigerator - Instructions

All installation instructions for PFS22SISBSS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PFS22SISBSS
226-240 of 381
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loud high pitched undulating whining.

  • Customer: James from Mesa AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
We have put up with this noise for several years and finally couldn't take it anymore. After research on the internet and reading about other folks solving the problem by replacing the main board, I ordered the main board and replaced it. That was a week ago. It has been a week blessed with SILENCE from the refrigerator. Hallelujah!!! It was an easy (if expensive) fix and the instructions were spot on. Anyone have a use for a defective main board?

Ice maker was leaking

  • Customer: Robert from Pampa TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watched the video that showed how to disassemble the ice maker. Then went right in and replaced the part and turned it on. It immediately started filling up the ice tray. I still have not been able to find out why it does not make as fast as the original ice maker. The tempeature for the freezer is set pretty cold.

temp to high in refrig

  • Customer: Russell from Port St Joe FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
pulled old off pun newon

Ice maker made no ice and no water from dispenser.

  • Customer: Lani from Lakeside CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...

The existing pan frame broke

  • Customer: Venkat from Cary NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the old one out and installed the new one in. Wasn't difficult at all.

No dispensed water or ice, repeated clicking sound, compressor not running

  • Customer: Dewey from Madison AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed power, removed control panel cover, removed control board, installed new control board.

Plastic part of icemaker broke

  • Customer: Robert from Glen Ellyn IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and then read the instructions. Emptied and cleaned freezer compartment. Removed old unit and removed part of old unit to be used in new installation. I then installed the new unit and turned the water back on. I let the unit produce over night and through the first batch of ice away. Because of the various regrigerators this ice maker was used I had a little confusion recognizing our model, but worked through this problem useing some common sense. All around I'm very satisfied with the results.

Erratic evaporator fan and compressor operation

  • Customer: Thomas from Midlothian VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
We had been told at some point the main control board would need replacement, due to various system issues with the refrigerator. The total repair cost would have been close to $400. The cost of the board was less than half of that cost. The instructions provided by PartSelect were very good. There was also a video of a similar model of refrigerator that outlined and showed every thing step by step. I removed the screws from the access panel in the back of the unit. unplugged the electrical plugs, removed the board. Installed the new board, reinstalled the plugs (all were idiot proof as PartSelect indicated), reinstalled the access panel and plugged the refrigerator back in. It has worked like new since install. This is an excellent website and service. I will use it again as needed with all my appliances.

Ice maker leaking

  • Customer: Don from Horseshoe Bay TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Quite easy. Turn off water supply and turn off ice maker at switch inside freezer. Unscrew the old unit, separate the electrical connection, and pull it out. New unit comes with parts that do not fit my refrigerator, so visually examine the new and old units, reuse any needed parts from the old unit, such as plastic water ramp. Reconnect the electrical connector, and screw it back in. Turn water supply back on and then turn ice maker back on at switch inside freezer. Discard unused parts. Wait up to 24 hours for new ice cubes to be made.

No ice!

  • Customer: Jacob from Waggaman LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Literally took out one screw and a wiring harness. Removed the old plastic piece off of the old ice maker and put on the new one.Installed new ice maker with the one screw and plugged the wiring back in.DONE!

Refrigerator not cooling either freezer or refrigerator sides

  • Customer: JAMES from JEFFERSON MD
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Found refrig. not working properly. removed back cover to access compressor and condenser fan motor. Fan motor turning very slowly if at all. Compressor tripping thermal overload. Blew out condenser coil of all dust. Figured it was either a circuit board or cond. fan motor. Went online to Parts Direct and read through other blogs of issues with this appliance. I ordered both the fan motor and circuit board. Replaced circuit board first. started it up and fan ran great. Compressor however kept tripping overload. All that overheating stressed that start relay so I disassembled and removed relay and thermal overload. Sure enough, relay was all broken up inside. I put a 3 in 1 hard start kit on it from a local supply house and it now runs great. I will order the new o/l and relay so I can remove hard start kit.

The frig was not cooling in main section or freezer

  • Customer: James M. from Belfair WA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered 3 temperature Sensors Part#PS304103 and viewed the video. Got there, opened the frig. and it looked totally different and no place in any part of this frig. that took these sensors as viewed on the video. Totally baffled why these parts were listed for this frig. there was no place in this frig that would access for these parts. Serial # was HR443071.Maybe this model is out of date for these parts. Trying to find someone who can repair it. Any ideas???Purchased this GE in 2008. Model #is GSS25WSTFSS Thanks, for your help. JIM

Fridge was warming but freezer was cold

  • Customer: John from Methuen MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I first thought of the board because it seems to be the most common problem but after a process of elimination I found it to be the evaporator fan which was relatively easy to disassemble and re-install. I am not a repair man of any sorts but spending $45 is much better that buying a new fridge. All is working well and my wife is happy.JG

Refigerator stoped working all lights off

  • Customer: robert from auburn CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
After reading some of the reviews. I bought and replaced the main circuit board. The parts came quickly and the job took very little time. Good time to remove all the panels on the back and clean the dust off everything. Refrig. is running great now! Easy fix! Thanks to all the help.

Ice dispnser worked intermitently. My diagnosis led me to the freezer door light switch. Switch operated the light but stopped the ice dispenser. After replacing the switch the dispenser operates every time now. problem solved.

  • Customer: Jeffrey from Poestenkill NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Little difficult getting the switch out, had to pry wth some force. New installation was real easy.
All Instructions for the PFS22SISBSS
226-240 of 381