This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the micro...
$10.58
In Stock
Order within the next 4 hrs and your part ships today!
There are two different couplers (also known as a turntable shaft) that can be used for this tray - a male D-shaped shaft and a female D-shaped shaft. The couplers are sold separately.
$106.23
In Stock
Order within the next 4 hrs and your part ships today!
This is a replacement oven lamp for your microwave. The base is made of black plastic, and the lamp itself is made of glass. The base is approximately 2 inches long and 1 inch wide. The bulb is locate...
$24.87
In Stock
Order within the next 4 hrs and your part ships today!
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bob
December 18, 2019
How to remove cover to replace door inter switches
For model number PEB1590SM2SS
Hello Bob and thanks for writing.
The interlock switches are located inside the cabinet and are activated by hooks or latches on the door. Unplug the unit and remove the cabinet There are screws left an right on the cabinet sides, once you have taken them off you can lift the cabinet.
The interlock switches will have wires attached to the terminals marked common (C) and normally open (NO). You can check the switches for continuity using a multi-meter. The closed-door will depress the actuator button on the switch; you should see continuity between these terminals. When the door is open there should be no continuity, and if there is the switch needs to be replaced. We hope this helps. Please contact us anytime.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Michael
2 days ago
Light is on, but the microwave doesn't function. What needs to be replaced?
For model number PEB1590SM2SS
Hello Michael, thank you for your inquiry. Based on our understanding of the issue, we would suggest checking the control board, part number PS11771852, to solve the problem. We hope this helps.
Turned out the issue was easily solved by replacing a single, inexpensive fuse.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic
... Read morerowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
Remove shroud . Two black philips head screws on side, and several on the back side. The two bottom screws on the back are special screws that a philips,straight slot, or hex screwdriver will not remove. I took a dremel tool with a thin metal grinding disc and created a straight slot through the centr of the two bottom screws. This allowe
... Read mored their removal with a straight slot screwdriver. Slide the cover straight back and off. The bulb is located on the top of the microwave connected with one screw. Replaced the bulb. It has two prongs that fit into the holder. Replace screw. Slide cover back on. It slides into retaining splines on 3 sides. Replace screws, and you're in business.
