PDW9980L00SS General Electric Dishwasher - Instructions

The dishwasher was disconnected and pulled out. I turned it over onto it's side so I could get down to the drain pump. It looked exactly like the original part and fit just as well. The hoses came right off and then once it was replaced, slipped right back on. It all worked like a charm. The only problem I had was after the repair. The copper water line moved around too much and caused a leak at the connection at the dishwasher. Luckily I tested the line outside before I reinstalled it completely. I just went and bought an $11 flexible hose with new fittings on either end and replaced the copper lines. It went on easier and it sealed tight.

This was a pretty easy repair and I am glad I did it. We were on the verge of just buying a new one, but for a $35 part and a couple hours, it was well worth it.

First I had to unscrew screws under the counter then pulled built in dishwasher out from under the counter, attached hing arm link to right side bracket on door, and the other end I attatched to a spring at the back of the unit. Thats it! and pushed the dishwasher back into place. All back to normal....by the way Im a 67 yr old great grandmother...

I took out the old rack and put in the new rack. Took about 20 seconds tops. But I had thought I needed to order the wheels (8 of them) and the wheel attachments (8 of those, too) separately because when you go to order the rack, it is suggested that you buy those, too. But the rack came with all the parts I needed so I ended up returning the stud rollers. Very happy with the product and the friendly service.

The repair was very easy, I just had to replace some bad bearing slides in the drawer pull. Remove the end cap, remove the top drawer, remove the old bearing slide from the drawer slide and snap the new one in. finally replacing the end caps.
Ordering the parts was easy and delivery was fast.

This was a piece of cake. The original soap dispenser never worked right and always left unused soap. The new part was easy to install and works great. Only needed a 1/4" nut driver and philips screw driver to pull the outside panel and replace the module rinse and cap assy. Easy!

replaced it

Removed Dishwasher, inverted it and replaced the sump housing. There are 2 screws mounting the top of the dishwasher to the counter, a water connection and the electrical connection. Remember to turn the water off and the electricity off. Slide the DW out on carpet. Carried it to the garage to affect the repair. Reinstalled the dishwasher. Most difficult part of this is that the water hose is really short. I used a 6ft extension so that the next time I have to pull this out it will be easier.

Turned spray arm while lifting upward to remove the old part. Place new spray arm over the water outlet and turned with light downward pressure until properly seated.

It less time to do the repair than it took to open the box and unwrap the part!

Exactly as described by a previous reviewer. I pulled out the old rack, put in the new rack and just moved over the cutlery rack.

Once we ordered both the "Stud Roller" and "Roller Lower Rack" the repair was simple.

The previous studs mostly disitegrated, so their removal was not an issue. The wheels pulled off easily.

I recomend getting new studs and rollers for all of the wheels on your rack. For me, that was 8 wheels and 8 studs.

First, take the rack out and flp it upside down in a convenient working space. Next, remove all of the old wheels and studs from the rack and discard. Then, snap the new wheels on to the new studs. Next, atached the stud (with the wheel) to each of the 8 spots on the rack. Put the rack back in the dishwasher and walla!

I can't beive that I waited almost two years to make this simple repair.

I pulled out the racks and decided to take off the upper (mid) arm. It came off with an adjustable wrench. When I looked at the arm I could tell that some of the holes were blocked. Some debris had gotten lodged in the holes and were blocking the water flow. I used tweezers to remove the debris and it solved the problem. I then pulled out the lower arm and cleaned it with warm water. There were soap deposits and I wondered if other debris could be blocking this as well. Finally I went onto the web site and saw that for $40 including shipping I could replace these parts with brand new parts. I did and the machine washes like new again.

Took out old basket, took off the sprayer arm and put it on the new basket.. pulled out the old wheels on the side tracks and slid the new basket in...pretty simple...

Detached the dishwasher from the cabinet. Slid it out. Removed small guide wheel that the cable went through. Removed the old broken cable. Replaced with new cable. Replaced the guide wheel. Hooked the cable to the door. Hooked the other end to the spring and hooked the spring to the body of the dishwasher. Put some WD40 on the the cable guide. Slide the dishwasher back under the counter and attached it to the cabinets. All done.

Remove screws holding old hose. Attach clamp to new hose with nut driver. Tighten hose and clamp around attachment.

Easy as cake. Perfect part!

Removed original silverware basket from dishwasher rack. Replaced it with new silverware basket. Placed original silverware basket in recycle bin (plastic content). So easy, even my 24 year old son could do it!