Models > PDW9280N00SS > Instructions

PDW9280N00SS General Electric Dishwasher - Instructions

All installation instructions for PDW9280N00SS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PDW9280N00SS
271-285 of 304
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

rusted racks

  • Customer: aaron from las vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
had old racks ou5 and new ones in w/in 15.

Wheel axle no longer stayed attached to lower basket

  • Customer: Paul from Fayetteville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
The repair was very simple. Remove the wheel for the lower basket then remove the old axle from the wheel. Insert the new axle and then reattached the wheel on to the basket.

wheel axels no longer held wheels on

  • Customer: Ellen from Fort Wayne IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It took all of 5 minutes to replace the wheels on the lower rack of my dishwasher. I just had to remove the old wheels and put the new ones on. I also replaced the tub gasket. This took maybe 10 minutes to push the new gasket into place.

dishwasher was not filling with water

  • Customer: Robert from Wantage NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very happy with the product and fast shipping. removed kick plate from dishwasher, inlet valve was on the front left bottom slid out dishwasher removed two screws and disconnected water line,and installed new inlet valve,very simple job if your somewhat handy,make sure you use thred sealant on water line when re installing

Wheels always falling off.

  • Customer: Beverly from Aurora CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Repair was just a snap I used a screwdriver to push out the old wheel axle and snap the new back in. This has solved my problem of the wheels falling off, it was driving me crazy every time I used my dishwasher the wheels would off. If are having problems like me this will solve your problem.

Installation video

  • Customer: Charles from Walnut Creek CA
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed front panel and replaced new part. Timer did not work because plug kept disconnecting. Called GE service and watched him remove panel without removing control panel. Plug for timer can be installed easily and front panel replaced without disturbing cable.

Some of the wheels had broken and I was having to lift the rack every time I filled up the dishwasher because it would not slide in.

  • Customer: Felicity from Mobile AL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took the rack out and turned it over on my kitchen counter. I then clipped on the new axles and pushed on the wheels. I wish I had found your site sooner , I can't believe how simple this was.

Dishwasher would not dry dishes

  • Customer: Kevin from De Soto KS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The quiet power 3 has the heating element in the back, so remove the screws holding the unit in place. Remove the bottom cover and disconnect the water inlet pipe, (after turning off the water of course). Discard the copper tubing if applicable, and pull dishwasher out until you can tilt it forward. Unsrew the plastic nuts and remove the wires for the element. Test the old one to make sure that you need to replace it. When sure of the problem reinstall in the reverse order. Replace the copper with stainless steel braided line and test.

Detergent dispenser would not latch

  • Customer: Michael from Ocala FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Repairs do not get any easier than this. Remove 12 screws to disassemble door panel (be careful not to let front panel of assembly to drop or bend when screws release it). Remove 6 screws to remove old detergent dispenser. Unplug cable from old dispenser. Connect cable to new dispenser. Install new dispenser into door with 6 screws and then reassemble door panel with 12 screws making sure to keep all wiring free from pressure points.

Old rinse aid cap melted by heating element

  • Customer: Eric from Stephens City VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply screwed in the new rinse aid cap to replace the old one

wheel fell off and axle was broken

  • Customer: andrea from littleton CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Took the bottom rack out and put axle and wheel on. Very simple to do. Took about 5 min. Would recommend this site to anyone. Thanks a bunch !

missing screw for Spray Arm

  • Customer: Russell from Rosharon TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove top rack stops, slide out upper rack from rack railing, turn over upper rack and attach spray arm using spray arm bearing and screw. Reassemble in reverse order.

GE Monogram Dishwasher Silverware basket bottom broken on bottom

  • Customer: Eddie from Boston GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Replaced identical basket. Service was outstanding from Part Select. Basket was delivered in less than 24 hours from time of order. Truly amazing.

Old wheels would not stay on (clips were worn)

  • Customer: Robert from Clayton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took out lower rack, turned upside down on flat surface, popped off old wheels. Pressed new axle into new wheels and snapped them directly to the lower rack.where old wheels were attached. A slam dunk..

tear in the tub gasket

  • Customer: Edward from Granite Bay CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled out the old gasket and replaced with the new gasket. Inserted the steel spring clip into the ends of the gasket. Repair complete.
All Instructions for the PDW9280N00SS
271-285 of 304