Models > PDW9280L00SS > Instructions

PDW9280L00SS General Electric Dishwasher - Instructions

All installation instructions for PDW9280L00SS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PDW9280L00SS
76-90 of 277
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Wheels on the bottom tray

  • Customer: James from Draper UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
It only took 10 minutes and they had the right parts and I got them in 2 days. I am ashamed to say that I let this go for a couple of months and for about $20 and 10 minues, I was able to take care of the the issue. The3 wife is thrilled.

Lower rack wouldn't roll because axles were broken

  • Customer: Kenneth from Bothell WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Unsnapped the wheel axle from the rack. Separated the axle from the wheel. Attached the new axle to the wheel. Snapped the new axle on the rack. Repeated for all 8 wheels. Solid.

detergent cup latch broke

  • Customer: Steven from Delanco NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Very easy - remove the screws around the inside of the door. 6 screws and 2 plugs to remove the assembly. Just be careful not the strip the sheetmetal screws when putting it back together. No screwguns...

The old wheels were continuously falling off the lower rack. We had to lift the rack in and out of the dishwasher - total pain in the neck.

  • Customer: Katie from Racine WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I removed what few remaining wheel assemblies there were - just pulled them off - no tools needed. Then I assembled the new wheels and wheel axels and simply snapped them on to the lower rack! It was a piece of cake.

wheels that allowed racks to roll on were broken

  • Customer: Nancy from Cincinnati OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Removed broken wheels & clips from the lower rack. Easily replaced the clips and wheels with the new clips & wheels which are better built then original. The dishwasher now operates better then in its new state because the bottom rack sits higher and the bottom arm swings more efficiently and the dishes are coming out cleaner.

Wheels falling off bottom drawer

  • Customer: SANDRA from MENDOTA HEIGHTS MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Very annoying problem with wheels falling off of the bottom dishwasher rack. Thanks to good advice here, purchased wheels AND wheel axels. Axels snap into the wheels, and the wheels snap on the bottom rack. Wheels are wider that the originals, and these snap ons are a much better design. Rack rolls in and out better than brand new!!

Wheels kept coming off dishwasher basket upon pull out

  • Customer: Glen from Garland TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
I hand removed the snap in wheel axels and replaced the axles with new ones, by hand, no tools needed. On this dishwasher basket the wheeel axels just snap onto the metal cage "wires" of the roll out basket holding the dishes. Very simple. Used pliers to squeeze each old axle retaining nubs,from each of the eight wheels, , then just slipped (pulled the wheels off the axles) and discared only axles (that here the problem, detaching frequently from grasping the pull out dish basket, due to heat taking the temper out of their gripper (to basket).

Soap Dispenser latch broke

  • Customer: Vicki from Mooresville NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
I removed six screws and unplugged the module and removed.
Replaced by the new module and plugged in and then replaced the six screws.
Very easy to fix.

wheel axles broke off from lower basket--deteriorated from age and almost daily use of dishwasher

  • Customer: harry from west seneca NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
old axles were removed by pulling wheel assembly from lower basket pins. squeezed old axle with needle nose pliers and discarded broken wheel axle. snapped wheels in place on new wheel axle and snapped wheel assembly into place on the basket. i replaced only two axles since the remaining ones were still intact. actual repair time was under three minutes. if all eight wheels would have to be replaced, i'm positive it would have taken no more than five to six minutes. in fact, the new wheel axle is a much better design than the original.

Lower rack jamming and hitting washer arms

  • Customer: Matt from Simi Valley CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I first tried the local appliance shop i got the wrong parts twice. I then wrote the model and serial #'s of my unit and found parts select. Got the right parts quickly and all I had to do was pull the old rack out and slide the new one in. Viola she was done ! Thanks Part Select !
Matt Hansen

Broken axle on one wheel

  • Customer: Andrew from DeWitt MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Only one axle was broken, but I replaced all 8 because GE had redesigned the axle to prevent future problems. Decided to just replace them all and be done with it. Took 10 minutes, start to finish and all is well.

broken wheel axel because it is not made to sterdy

  • Customer: Anthony from Colonia NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
took out broken wheel axel and replaced it with a new one

cap was melted

  • Customer: Greg from Doon IA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
replaced it

a couple of my wheels had broken

  • Customer: Carol from Henrico VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I replaced the wheels and axels with the ones I bought and now it is fine.

Lower dish rack wheels and axles were broken and off.

  • Customer: Curtis from Elkhorn WI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Removed rack from dishwasher, put axles in wheels and replaced onto lower rack. Used new design axle in replacement, seems to be an excellent fit.
All Instructions for the PDW9280L00SS
76-90 of 277