Quick Question!

Have you ever purchased from PartSelect.com before?

Models > PDW9280J00SS > Instructions

PDW9280J00SS General Electric Dishwasher - Instructions

All installation instructions for PDW9280J00SS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PDW9280J00SS
91-105 of 292
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

soap dispenser was not staying closed....

  • Customer: Erin K. from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
hubby had no prob replacing the new part!!YEA!!dishes are clean again!

Lower rack wouldn't roll because axles were broken

  • Customer: Kenneth from Bothell, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Unsnapped the wheel axle from the rack. Separated the axle from the wheel. Attached the new axle to the wheel. Snapped the new axle on the rack. Repeated for all 8 wheels. Solid.

Soap Dispenser latch broke

  • Customer: Vicki from Mooresville, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
I removed six screws and unplugged the module and removed.
Replaced by the new module and plugged in and then replaced the six screws.
Very easy to fix.

wheel axles broke off from lower basket--deteriorated from age and almost daily use of dishwasher

  • Customer: harry from west seneca, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
old axles were removed by pulling wheel assembly from lower basket pins. squeezed old axle with needle nose pliers and discarded broken wheel axle. snapped wheels in place on new wheel axle and snapped wheel assembly into place on the basket. i replaced only two axles since the remaining ones were still intact. actual repair time was under three minutes. if all eight wheels would have to be replaced, i'm positive it would have taken no more than five to six minutes. in fact, the new wheel axle is a much better design than the original.

Wheels kept coming off dishwasher basket upon pull out

  • Customer: Glen from Garland, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
I hand removed the snap in wheel axels and replaced the axles with new ones, by hand, no tools needed. On this dishwasher basket the wheeel axels just snap onto the metal cage "wires" of the roll out basket holding the dishes. Very simple. Used pliers to squeeze each old axle retaining nubs,from each of the eight wheels, , then just slipped (pulled the wheels off the axles) and discared only axles (that here the problem, detaching frequently from grasping the pull out dish basket, due to heat taking the temper out of their gripper (to basket).

Lower rack jamming and hitting washer arms

  • Customer: Matt from Simi Valley, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I first tried the local appliance shop i got the wrong parts twice. I then wrote the model and serial #'s of my unit and found parts select. Got the right parts quickly and all I had to do was pull the old rack out and slide the new one in. Viola she was done ! Thanks Part Select !
Matt Hansen

Broken axle on one wheel

  • Customer: Andrew from DeWitt, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Only one axle was broken, but I replaced all 8 because GE had redesigned the axle to prevent future problems. Decided to just replace them all and be done with it. Took 10 minutes, start to finish and all is well.

wheels kept falling off

  • Customer: karen from St Charles, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
It was very simple to install. At first my husband thought I had ordered the wrong part. I guess they just revamped the part and it worked out really well. And I didn't have it mailed special but I got the parts in about 2 days. My only problem is that the shipping cost as much as the parts.
But the parts are installed and the wheels don't fall off anymore!! If I need anything else I will use your company again and I will tell friends and family about you guys.
Thanks

slow leak from the pump while operating

  • Customer: rick from greensboro, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 4 people found this instruction helpful
followed instructions that came with the part. My dishwasher had a slightly different configuration than what the directions said so disassembly took a few minutes to figure out. Once that was done, the removal of the old impeller assembly and installation of the new went quite smoothly. The replacement assembly had a "grater" which was not present on my original however it installed perfectly and no longer leaks.

Wheel axle clips broken

  • Customer: Jerry from Spring, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Just pulled the old axles out and snapped the new ones in and slid them on. Wish all household repairs were this easy.

The lower rack's wheels were coming off

  • Customer: Ricardo from Miami, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
The parts came really fast, I did not even have time to think about them...when they came I was like what? They are here? WOW! anyway, I just changed the wheels with the new axel and perfect! now it works wonderful...and it was so easy! I can't believe I dealt with that for as long as I did.

broken wheel axel because it is not made to sterdy

  • Customer: Anthony from Colonia, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
took out broken wheel axel and replaced it with a new one

Wheels falling off bottom drawer

  • Customer: SANDRA from MENDOTA HEIGHTS, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Very annoying problem with wheels falling off of the bottom dishwasher rack. Thanks to good advice here, purchased wheels AND wheel axels. Axels snap into the wheels, and the wheels snap on the bottom rack. Wheels are wider that the originals, and these snap ons are a much better design. Rack rolls in and out better than brand new!!

wheels that allowed racks to roll on were broken

  • Customer: Nancy from Cincinnati, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Removed broken wheels & clips from the lower rack. Easily replaced the clips and wheels with the new clips & wheels which are better built then original. The dishwasher now operates better then in its new state because the bottom rack sits higher and the bottom arm swings more efficiently and the dishes are coming out cleaner.

The old wheels were continuously falling off the lower rack. We had to lift the rack in and out of the dishwasher - total pain in the neck.

  • Customer: Katie from Racine, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
I removed what few remaining wheel assemblies there were - just pulled them off - no tools needed. Then I assembled the new wheels and wheel axels and simply snapped them on to the lower rack! It was a piece of cake.
All Instructions for the PDW9280J00SS
91-105 of 292