This dishwasher door gasket, or door seal, allows the dishwasher door to have an airtight seal when closing the door. No tools are required for this installation, simply remove the existing gasket and...
This upper dishwasher dishrack roller, also known as a dishrack wheel, allows you to roll the dishwasher rack easily on the support rails. If your dishwasher rack is disconnected or the rack is broken...
The door spring retainer is used in dishwashers. It attaches and holds the door spring to the support frame. If your dishwashers door keeps crashing, or both the door and dish rack are falling apart, ...
This silverware basket has eight sections and is all white in color. It is also made of plastic and has a built-in handle on either side so that you can quickly and easily remove it from the dishwashe...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This genuine inner door foam insulation strip, sometimes known as bottom seal foam, is used to create a waterproof seal that helps prevent leaking from the door area of the dishwasher. The existing in...
This water inlet valve is specially designed for those dishwashers of the vertical axis style and comes with a mounting bracket. The attaching solenoids on the valve open and close according to the de...
The short dispenser door retaining pin latches your washing machine door to the hinge. If you find that your washing machine will not dispense detergent, or the lid will not latch properly, you may ne...
Sold individually. This part is exactly 1 inch long.
$10.63
In Stock
Questions And Answers for PDB4600AWE
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jack
October 19, 2023
Dishwasher is not cleaning. I want to take each part out and clean them. I have successfully got down to the discharge pump removed the three screws bot the part does not lift off like the repair video shows. Something is keeping it from lifting off. It is lose but it is not free to lift off. I don’t want to break it so I need advise how to remove it so I can get to the impeller pump and drain impeller.
For model number PDB4600AWE
Hello Jack, thank you for contacting us. We have attached some relevant instructions, which may not be of the exact same model but will help you get to the drain pump and drain impeller pump. After you remove the screws of the discharge pump, you just need to pull it up. After that, pull off the micro mesh filter. Remove the mounting screw to release the old wash impeller. Lift off the suction plate filter support and cutter. Remove the screws and pull off the drain cover. Use a screwdriver to pry off the old drain impeller. We hope that helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Took out about 7 torx screws to remove the inner door liner. Discovered evidence of leak coming from the sop dispenser latch, and noticed the grommet had turned soft and was torn. The grommet is only about 1" square. Used nut driver to remove two screws to remove latch assembly. Slipped old grommet off and put new one on, and reattached t
... Read morehe latch. The foam seal at the bottom of the door looked worn, so we replaced it with weatherstripping from home improvement store. The main door seal was brittle, so we replaced it too - just grab an end and pull the old one out. The new one was installed by starting at one end and we just pushed it in place. We used a nut-driver to push it in - we were afraid a screwdriver might damage it. The new door seal required us to latch the door to get it to stay closed the fist couple of days, but now it has loosened up a bit and works as expected. And NO MORE LEAKS. Cost is much less than a new unit!
I opened the end stop of the rack, replaced the roller, and put the end stop back on. I can't believe I paid the repairman the last time $125????? An he put in a regular screw that rusted and broke the roller. Took me 3 minutes! Thanks