Quick Question!

Have you ever purchased from PartSelect.com before?

Models > PAVT234AWW > Instructions

PAVT234AWW Maytag Washer - Instructions

All installation instructions for PAVT234AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PAVT234AWW
76-90 of 378
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Noisy pump

  • Customer: Brian from Gobles, MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 8 of 13 people found this instruction helpful
My pump was making noise. I thought it was dying on me. I ordered the replacement part. Extremely fast shipping! Only a couple of days. Everything matched up, took the old one off, put the new one on and reconnected the drive belt. Works perfectly! Thanks so much.

both hinges on washer lid were broken

  • Customer: Harris from Ashland, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
if you move the agiatater all the way to one side you can acess the star screws from under the hinge then push the agitator to the other side and acess the screw on the other hinge , you dont have to remove the top of the washer, let me say i did not have the serial no and the people at part select were very helpful and pacient when i called and they got me the RIGHT part the firdt time.thanks again for all your help the job came out perfect and saved me a lot of money for a repair man. ASHER

loud noise durring spin cycle

  • Customer: Steven from Commerce, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 11 people found this instruction helpful
I removed the plate at lower left corner on rear of washer 3 screws and it pops right off after that there are 2 clamps on the hoses attached to the pump I removed those with pliers then I removed the 3 screws holding the pump to the bottom of the washer then pulled the pump through the hole and replaced it with the new pump installed all the screws then layed washer on its side and replaced the belt set it up pluged it in and no more noise sounds better than new. Thank you Part Select for making it an easy painless task to get the parts I needed.

Washer Spin Cycle Stopped

  • Customer: Diana from La Mirada, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Removed the screw from the side of the lid of the washer. Took off the old Lid Switch Actuator and screwed in the new one. Took a little elbow grease because the old screw was tight but no longer than 15 minutes tops.

Noticed nick in drive belt durng inspection and cleaning

  • Customer: Brian from Plainville, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 5 people found this instruction helpful
Washer was making noise especially when spinning. I took the washer apart to clean it, That is what it really needed. Also adjusted the water level to prevent overflows which caused soap and water to get underneath into the drive belt area as well. During inspection noticed a nick in the drive belt, Although this was not really causing immediate problem wanted to repalce it to prevent problems. Ordered the belt; it came in two days with no special postage. To install, just leaned the washer over on its front on a slight incline. Took old belt off and put new on by turning the big pulley. It is spring tensioned, so no tools. This may be the easiest part repacement I ever did. Took longer to write this paragraph than to repalce the belt.

Water would not shut off after filling desired level

  • Customer: Richard from Geneva, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 6 of 8 people found this instruction helpful
Took out the two top screws out that hold the top down on the back so you can lift the lid up. Removed the cover plate on the back. Take out the screw that holds the valve in place. Reach up through the access panel and undo the to clips that hold the hose and wiring. Lift the lid up and pull the unit up and remove hose and electrical connections and put back in reverse order. Very simple to do.

Severly off balance during spin cycle

  • Customer: David from Duluth, GA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 8 people found this instruction helpful
My washing machine was severely off balance during the spin cycle. It would bang violently against the side and “walk” across the laundry room. I was able to fix this for under $25 dollars of parts from partselect.com and a few hours. I rated the task as easy, but I am somewhat mechanically inclined. Others may find it a bit difficult but I believe anyone except an absolute beginner can do this job.

Fix this problem before significant damage is done to your base! Otherwise the job will take more time and be a LOT more expensive. My base had experienced a little damage but thankfully it did not require replacement. When the snubber wears out, it allows the tub to rub against the base. Metal on metal is never a good thing.

Also I chose to replace the springs, even though it may not have been 100% necessary. You have to take them off anyway and they are inexpensive. It is easy to know when a spring is broken, but not as easy to know when it has lost some of its spring. Just makes sense to me to replace them.

I used the directions below which I found on the internet. They are listed below unedited by me. I have added a few of my own comments below that.

• Remove power and all hoses
• Lift top by inserting putty knife just inside front clips to release
• Remove front and rear panels, 10mm
• Disconnect drain hose from bottom of drum, pliers - spring clip
• Remove 6 springs from bottom of drum using channel lock or spring tool
• Lay on side, remove drive belt by turning large drive pulley and side tension to belt
• Remove water level hose on side of drum, pliers - spring clip
• Remove drum from cabinet by sliding out top. It is not necessary to remove drum from transmission.
• Inspect base plate for damage
• Lay drum on padded surface, upside down
• Remove C clip, drive pulley, being careful to observe order of parts and washers
• Loosen 6 screws holding down old snubber. DO NOT REMOVE SCREWS, THERE IS A VERY STRONG SPRING UNDER THIS PLATE. Loosen screws only enough to get old snubber out.
• Clean dust from area.
• Insert new snubber, keeping it even while tightening screws.
• Reverse other processes above to assemble washer. Replace any broken drum springs. Replace belt if worn.

My tips:

• After you remove the tub you will see a lot of fine white dust in the bottom of the washer. That is from your old worn out snubber. Vaccum it out.

• I didn’t have a spring tool but I found that using a pair of vice grips to remove and replace the springs was easier than using channel locks.

• Technically, I believe the clip is actually called an e-clip. If you have the correct tool for this removing and replacing it will be a lot easier. I did not have the tool. I used an open end wrench that was just the right size to butt up against the two ends of the clip. A light tap with a hammer against the other end of the wrench and it popped right off. I used a pair of needle nose pliers to put it back on.

• Also regarding putting the e-clip back on, at first I could not see the groove that the clip was supposed to slid into. It was below the little plastic piece with the teeth. I used a small flat screw driver inserted into the groove to gently pry it up and had someone gently tap on the plastic piece which pushed it down enough to expose the grove.

• I highly recommend heeding the warning regarding the loosening of the 6 screws holding the snubber. I did not have any trouble with this but there is a 200 lbs spring underneath that you do not want to release. It could injure you and might be hard to put back. Just loosen each screw 1/4 turn at a time until the snubber can be removed.

That's about it. I took me about 4 hours

Washer went off balance and the flume broke off

  • Customer: Michelle from Jupiter, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 23 people found this instruction helpful
I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!

washer was squeeling to a stop

  • Customer: paul from newbern, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 6 of 8 people found this instruction helpful
first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy

new belt worn out by a bad motor pulley

  • Customer: ALBERT from WASCO, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 6 of 8 people found this instruction helpful
i took off the old belt and i took off the motor pulley with the pliers and srewdriver. i put the new pulley in with my hand and gave it a hit with the palm until it snap in and then i put the belt on by rotating the main pulley on tub till the belt was pulley on.

Agitator was loose and wouldn't stay in place

  • Customer: Myrtle from HYES, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 5 of 5 people found this instruction helpful
First I removed the bolt and removed the old agitator and post assembly then I put the new agitator and post assembly in place and tightened the bolt. It was so easy, when I called the manufacturer they wanted to send out a technician, but thanks to Parts Select I fixed the problem without spending alot of money and without the hassle.

Loud squeal when spin cycle finished, white powder under washer

  • Customer: Kevin from Pooler, GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 5 of 5 people found this instruction helpful
Read DIY review from William, Middleton, OH on 01-15-08. Tip on how to relieve spring pressure on brake assembly worked like a dream (3ea 10-24X2 bolts/machine screws). Replaced brake and machine works like new and was an inexpensive fix. Once the shell/housing is off the machine, tub can be turned upside down and the base doesn't need to be removed. White powder under machine was a plastic wear ring that tells you when your brake rotor needs to be changed. Brake rotor still had lining but was much thinner than replacement part. Note* Use putty knife to push in clips on front to release the top lid section.

Leaking Water Pump

  • Customer: Edwin from Eagar,, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 6 people found this instruction helpful
Pulled wahser away from wall, unpluged, removed screws from rear access panel, removed hoses from water pump, used towell to absorb excess water still in pump and hoses, removed drive belt, removed screws securing pump, removed old pump replaced it with new pump, cussed a little when replacing hoses, repeated steps in reverse order, checked for leaks.

Cold water no fill

  • Customer: Christopher from Cincinnati, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 9 people found this instruction helpful
Always check the basics first!

Mistakenly replaced the water valve (even though it was buzzing idicating it had power and showed 110V across terminals). Assumed the water lines were working. Turned out to be a clogged cold water line (safety valve clogged). Replaced both lines for good measure, machine working fine.

Water wouldn't shutoff. Agitator would pop up and stop agitating

  • Customer: James from South Jordan, UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Opened up washer, found vacuum hose was broken and replaced it. Removed agitator with a couple extensions and a socket wrench. Found agitator part was worn out and replaced it. The best part was how great PartSelect made it so incredibly simple and easy to find the right part. I'm now a customer for life. Kudos PartSelect.
All Instructions for the PAVT234AWW
76-90 of 378