Quick Question!

Have you ever purchased from PartSelect.com before?

Models > PAV3300AKW

PAV3300AKW Maytag Washer - Overview

Get Parts and Repair Help for PAV3300AKW

If you know the washer repair part you need, you can browse the list of all parts on the PAV3300AKW, or you can search by name or part description. You can also find your part by where it is located on the PAV3300AKW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for PAV3300AKW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.76

Drive Belt - 51 inches long

This V-style drive belt is about 51" long and 3/8" wide. This part is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get we...

$7.88

Lid Hinge

This lid hinge in an inch and a half long and is used for some washing machines. It is all white in color and it is made entirely of plastic.

$6.77

Snubber Ring

$5.15

Suspension Spring

This suspension spring is used with many washing machines. It is made entirely of metal and is seven inches long.

$82.14

Drain Pump

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. NOTE: This is a redesigned part. The pump no...

$12.18

Lid Hinge Pin

This lid hinge pin is just over an inch long. It is all white in color and is made entirely of plastic. Sold individually.

$54.52

Transmission Pulley and Bearing Kit

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - t...

$7.01

Screw

This screw is sold individually.

$5.15

Hose Clamp

$5.15

Cover Screw

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

One of the plastic hinge pins brroke

  • Customer: Allen from North Little Rock, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 482 of 479 people found this instruction helpful
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated. read more

Washer jumping in spin cycle (white flakes under the washer)

  • Customer: David from Butler, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 233 of 242 people found this instruction helpful
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the complete drum out of... read more

Pump was making a grinding noise

  • Customer: Ranse from Layton, UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 232 of 248 people found this instruction helpful
The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A small amount of wate... read more