Quick Question!

Have you ever purchased from PartSelect.com before?

Models > PAV2300AWW > Instructions

PAV2300AWW Maytag Washer - Instructions

All installation instructions for PAV2300AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PAV2300AWW
106-120 of 517
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer was squeeling to a stop

  • Customer: paul from newbern, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 6 of 8 people found this instruction helpful
first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy

Cold water no fill

  • Customer: Christopher from Cincinnati, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 6 of 9 people found this instruction helpful
Always check the basics first!

Mistakenly replaced the water valve (even though it was buzzing idicating it had power and showed 110V across terminals). Assumed the water lines were working. Turned out to be a clogged cold water line (safety valve clogged). Replaced both lines for good measure, machine working fine.

washer making pounding and rocking sound

  • Customer: serenade from charleston, SC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Took a screwdriver and pried up the top of washer, then reached in and unscrewed the front two screws that allowed the front to be lifted off.
Removed two screws on lower right side that allowed us to pry open right side of washer. There are six springs along the bottom of washer that keep the tub stable and keep it from bouncing against sides while in spin mode. One of the springs broke and needed to be replaced. Off course it was the one that was in the far back and the hardest to get too. But by prying open the right side it was reachable. The wife pushed against the tub to make the spring stretch a little less but still was too difficult. We took the advice of another home repair guy and put quarters in the spring (about $1.75 worth) to make it stretch out, then it was simple to connect the two ends, remove the quarters and voila....it was done. Screwed theright side back on, but the minimum order on the springs was six and the others seemed fine, we just put the other five inside the washer cabinet, replaced the front panel, reset the clamps on top of the front panel, slammed the top down and we were back in business. The parts including shipping was a little over $10.00. So I am sure we saved at least $140 repair job.

broken pump, burned belt

  • Customer: Jeffery from Omega, GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set, Wrench set
  • 5 of 6 people found this instruction helpful
I removed four screws to remove a plate to get access to the pump. Then I removed 3 screws to remove the pump. I then put the new pump in place and put the 3 screws back in the pump. Then I put the plate back on and put the 4 screws back in. Then I put the belt on and put the washing machine back in place and connected the water lines and drain line and plugged the washing machine back in and then tested the washing machine to make sure it worked. Job completed.

Leaking Water Pump

  • Customer: Edwin from Eagar,, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 6 people found this instruction helpful
Pulled wahser away from wall, unpluged, removed screws from rear access panel, removed hoses from water pump, used towell to absorb excess water still in pump and hoses, removed drive belt, removed screws securing pump, removed old pump replaced it with new pump, cussed a little when replacing hoses, repeated steps in reverse order, checked for leaks.

The timer would quit after the wash cycle.

  • Customer: Cheri from Crowley, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 6 people found this instruction helpful
1.Removed the back plate from the control panel. 2.Pulled out on the plastic pin (behind the timer) with needle nose pliers in order to release the timer knob. 3.Removed wiring plug and uncliped timer. 4.Installed new timer.

Water wouldn't shutoff. Agitator would pop up and stop agitating

  • Customer: James from South Jordan, UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Opened up washer, found vacuum hose was broken and replaced it. Removed agitator with a couple extensions and a socket wrench. Found agitator part was worn out and replaced it. The best part was how great PartSelect made it so incredibly simple and easy to find the right part. I'm now a customer for life. Kudos PartSelect.

agitator auger failure

  • Customer: Florian from Richmond, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 6 of 9 people found this instruction helpful
The parts list and schematic made it easy to select the correct part that my wife and I believed was the problem. The plastic part was removed easily because it kept on popping off during the wash cycle of anything other than light low loads. The mechanism was useless. With the new piece/part inserted the machine got back to business as it should be. Plastic just wears out to quick. At least we have delayed a machine replacement.

lid switch acuator broke and some cycles would not work

  • Customer: Brian from Woodbury, MN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
unscrew the screw holding the broken part in the lid to remove the old part and tighten the screw to a firm position to hold the new piece in place. Now working fine.

Water pump failure

  • Customer: John from Alhambra, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 6 people found this instruction helpful
Disconnect electricity....remove front panel by gently prying up lid.... Remove two small screws at corners of front panel. You may need small nutdriver here or very small hands, you can easily swivel tub out of the way....once front panel is off water pump is at the bottom right... It is only connected by two squeeze clamps and 3 nuts... This is obviously where the adjustable wrench and nutdriver come in very handy... Otherwise this job will be a bit longer....be prepared for residual water to pour out...you will need towels or a bucket....replace old with new one by reversing the process...at this point tilt the entire washer on it's backside or at least at a 45 degree angle to access the bottom... Swivel the motor away to slack up the belt...remove belt and replace in reverse order of diassembling.... Should take no more than 15 minutes.... Good luck!!!!!

water was not going to the barrel

  • Customer: HAMID from CHATSWORTH, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable), Wrench set
  • 4 of 4 people found this instruction helpful
first I thought there is a problem with with hoses.problems like filter or hoses blocked.after I opened the hoses they were fine .Water was going out with power .Then I opened the valve connected to the hoses . I checked these hoses withe help of a 12 volt battery . the valve was not opening so I came to the conclusion that this part is broke.is not easy to change this part.Small place and hard to unlock the hose inside .They could design this much easier with just using longer hose.But I think then nobody will call service dept.

It squeaks when stop spinning

  • Customer: Hing from Toms River, NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 6 of 10 people found this instruction helpful
I think normally the problem is caused by the Brake Rotor Lining Assy (item #50 on the diagram). It has a brake lining facing down that makes contact with item # 51. It turned out that I had grease & grime on these parts, thus the brake is not taking grip & causing squeaky noise. All I had to do was to clean the parts & put them back. I bought the part (#50) - P/N 2347192, but it was a whirlpool part that didn't fit my Magic Chef. Some parts fit both brands, but this 1 didn't. Here is the procedure:

1. Unplug washer.
2. Move unit away from wall.
3. Tilt it back far enough to work underneath. Support the front with lumber.
4. Pull out cap (#58)
5. Remove ring clip (#57)
6. slide out everything from #53 down. Keep them in same order for re-installation.
7. There are 6 ea screws (#53) that hold item #52 to item #45. It is spring loaded by item #47. Item #53 has a 5/16" hex head. Use 3 ea. #10-24 hex head screw, at least 1.25" long to assist in compress/decompress the spring tension. You can buy them from a hardware store.
8. Take out every other screw (#53) & replace them with these 3 longer screws for remove/re-installation of item #52.
9. Take out the remaining 3 ea #52 screws.
10. Go around & back off each of the 3 longer screws to decompress the spring.
11. Remove item #52, & everything from #48 down will come out.
12. Clean or replace what you need.
13. Do the reverse to put everything back.
14. There is an item within #59 that looks like a miniature bearing. I would put some grease on that & on item #55.

Washing Machine Walking during Spin Cycle

  • Customer: Daniel J from Cayce, SC
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 4 of 4 people found this instruction helpful
Looked up probable causes on PartSelect website. Determined that worn snubber ring and and weak springs were probable cause. Ordered parts on a Thursday. Parts arrived on following Monday.

Read several repair stories on the website. One story gave step-by-step instructions for disassembly. Very helpful since I followed this prescription. While waiting for delivery of the parts, I removed the tub and inverted it.

Removing springs was relatively easy. Did not remove snubber ring until new parts arrived, but replacing it was easy. I was very cautious about loosening the 6 screws and heeded the warning about the 200 pound spring under the cover.

Diagrams on website showing expanded mechanism of washing machine parts were very helpful for reassembly.

The most difficult part was installing the new springs, since they were quite strong. One repair story on the website suggested using coins to expand the new springs enough to be able to hook the springs into the upper slots and hangers.

I USED ONE OF THE MORE ACCESSIBLE LOCATIONS (AT THE REAR OF THE MACHINE) TO PREPARE EACH SPRING FOR INSTALLATION).

I hooked a spring in the bottom slot. I pushed a long heavy screwdriver through the spring's upper hook and the hole in the metal support and expanded the spring until I could insert 1/2-inch washers (about 8) between the rings. I prepared each spring this way for installation around the tub. With the washers in the expanded spring, it was relatively easy to use a pliers to lift the upper hook into the hole or hanger.

I decided to insert the spring next to the motor first since it was the more inaccessible. The remaining springs were installed relatively easily.

Reassembly was easy by following the reverse order of the disassembly instructions. I found the tub to be pretty heavy to lift, so when it came time to put it back into the frame, I turned the frame on it's side and inserted the tub from floor level.

I am very proficient mechanically but I believed I could make this repair without difficulty. I think that without the repair stories I had viewed on the website, it would have been more difficult. A spring tool would have been immeasurebly more helpful.

The washer was making a fine squeeling noise that created a foul burning odor

  • Customer: SONY from CONCORD, NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 5 of 7 people found this instruction helpful
Took the washer outside, turned the washer on its side to expose the bottom panel. Removed the old water pump (three screws and two hoses. Replaced with new water pump and connected all fittings. Real easy to do. Washer runs great now.

Washer lid came off hinges

  • Customer: Geoffrey from Knoxville, TN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
PROBLEM: The washer lid has two hinge pins that are attached to the lid with Phillips screws (one per pin). The plastic pin that inserts into the hinge broke off, allowing the lid to come free. SOLUTION: First, I removed the lid from the washing machine. Second, I used a Phillips-head screwdriver to remove the original hinge pins from the lid. Third, I replaced the hinge pins. Fourth, I used a flat-head screw driver to pry up the washer top to obtain easier access to the hinge screws. Fifth, I removed the original hinges with a Phillips-head screwdriver (one screw per hinge). Sixth, I attached the new hinges to the washer lid. Finally, I attached the hinges (and lid) to the washer top, then lowered the washer top.
All Instructions for the PAV2300AWW
106-120 of 517