Models > PAV2300AWW > Instructions

PAV2300AWW Maytag Washer - Instructions

All installation instructions for PAV2300AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the PAV2300AWW
61-75 of 517
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

High pitched screech from brake at end of spin cycles.

  • Customer: William from Lithia FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 11 of 11 people found this instruction helpful
I disconnected and moved the washer into the garage for optimum work space. Then I opened the top panel (by releasing the two retainer clips between the top and front panels with a putty knife inserted approx 2" in from each side) and taped a spacer block between the back of the tub and the back panel of the washer, to keep the tub from moving toward the back when the washer is tilted.

Then I tilted the washer back against my 2 1/2' high workmate bench (backstopped against the wall). After adjusting the tilt angle to provide adequate access to the bottom of the washer and insure it was was beyond the forward center of gravity, I began the repair.

Working from the bottom, I first removed the drive belt. Then the white dust cap, shaft retaining ring, plastic cam, pulley, and the various washers and bearings leading up to the brake assembly, making note of their order.

Then I removed three of the six 1/2" 10x24 brake stator retaining screws at alternating positions replacing each with one of the three 2" 10x24 screws I had previously purchased the hardware store. Then I removed the three remaining 1/2" screws, and slowly began to remove the three 2" screws alternating a few turns on each in rotation to evenly ease the 200 pounds of pressure from the brake rotor spring.

When the pressure was released, I removed the old brake stator and rotor and placed the new ones on the shaft, then re-compresed the brake rotor spring with the three 2" screws in alternating positions. Then placed three of the original 1/2" screws in the threee open positions, then replaced the three 2" screws with the remaining three 1/2" screws.

Then I reinstalled the remainder ot the parts in reverse order of removal.

Noise during spin cycle

  • Customer: CHERYL from HUDSON NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 12 of 14 people found this instruction helpful
Noise loudest during spin cycle. Wash cycle showed transmission was ok. Pump shaft loose in housing. Fix was just as described. Tip washer up, lift belt from pulley on pump. Remove rear panel access. Remove hoses. Un-bolt pump. New pump does not have metal base plate, it fits directly to base of washer. Bolt new pump to base in same orientation, attach hoses, tip washer up and slide belt back on to pulleys. Move belt by hand to check function. Reconnect washer to utilities and begin fill. Check for leaks at hoses. Replace rear panel cover.

Washer leaked water on the floor. Seal nut assembly rubber and o-ring were worn out.

  • Customer: Kevin from Houston TX
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 14 of 21 people found this instruction helpful
Overall, this repair should have been quite easy. The problem was removal of the old seal nut assembly. It was a bear to remove, and ultimately I had to surgically remove it from the washer in pieces. Unfortunately I broke the outer tub (plastic) in the process of getting the nut off. Once I had the silly plastic nut off, and the tub repaired the balance of the repair was absolutely easy.

My summary: This repair is really easy IF the plastic seal nut assembly comes off easily. If it doesn't budget easily, go ahead and chip it apart to get it off, being careful not to damage the threaded part of the agitator shaft. The new one will completely replace the chipped away nut.

The motor ovrheated,

  • Customer: Dennis from Merritt Island FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 11 of 13 people found this instruction helpful
I took the front pannel off just 2 scrwe was holdig the pannel,the motor was in ftont,4 bolt was holdig the moto,and it is very easy to change,

drive belt was squealing and slipping

  • Customer: Kevin from North Plains OR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 10 people found this instruction helpful
I wasted time opening up the metal container for the washing machine, which was easier than expected. The top simply pops off with a little bit of prying with a screwdriver, then the front panel is held in place with two sheet metal screws. The front panel then lifts off and you can see the exterior case for the tub drive mechanism and motor. But, it wasn't obvious what was wrong until I tilted the entire unit backwards and saw the drive belt available directly under the machine and fully accessible without any tools. It was obvious, because there was a 1/8" worth of belt fragment dust under the machine. A new belt was all it needed and after I ordered it from PartSelect, I simply jimmied the old belt off the main pulley and put the new one on. It no longer squeals or slips. Hopefully, I gained another 5 years of life out of the washing machine.

water pump was noisy

  • Customer: Patsy from Brookfield, MO
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 10 of 11 people found this instruction helpful
Removed the front panel, Removed the belt from pump in the back of machine. Removed the pump from the back of machine, Put the pump in reconnected the belt, Replaced all the screws. My husband did the repair work in a matter of 45 minutes. Machine works fine now. The part came when I was told it would. I am very pleased with your service.

Washing Machine was bouncing on every load

  • Customer: Hud from Woodruff SC
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 9 of 9 people found this instruction helpful
Diagnosed that the snubber had failed.
Removed the belt, cam assembly and pulley assembly. Using Maytag brake removal tool #12002012 I removed the brake stator. I removed the front of the washing machine and the rear access plate. I removed the six tension springs. I moved the machine basket and shaft assembly toward the top of the machine. I removed the old snubber and replaced with a new one. I installed 6 new tension springs and reassembled.
The washing machine runs great.

One of the two bolts that holds the motor in place broke off and since the bolts are actually embedded in the motor I had to buy the whole motor rather then just a 25 cent bolt.

  • Customer: Elmer from Fort Campbell KY
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 18 of 36 people found this instruction helpful
First I took the front shield off, then I took the motor off.

Washing machine beat itself to death during spin cycle

  • Customer: John from Cumberland MD
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 13 of 21 people found this instruction helpful
Removed front cabinet, removed 6 springs holding tub down, removed pump hose, removed drive belt from motor,lifted tub out the top and placed upside down, loosened all six hex bolts(did not loosen or remove drive pulley) backed all six bolts out and left 4 threads showing, slipped old snubber out cleaned all surfaces with alchohol and slid new snubber in. Put corn starch on base where snubber rides, lifted tub back in, hooked up all six tension springs with auto brake tool.put belt back on...done..no more beating itself to death.

The timer would quit in mid cycle. Spin did not drain the water in Permanent Press or Delicate cycles.

  • Customer: Dale from Benton LA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 11 of 15 people found this instruction helpful
I opened the front of the machine. The clips had rusted. One broke and the others were very difficult to work with. I pried the panel open with a large screwdriver. I took the back panel off to access the water pump. I removed the back panel on the electricals to access the timer. To replace the timer I pried off the decorative cover. To get the knob off you have to squeeze in on the timer split shaft while pulling out on the know. This was the second hardest part. (The front panel access was the most difficult). After that the timer clip is easy to loosen and it slides a littel then pops out. Electrical connection was obvious. The motor sping was the next most difficlt part. The spring fits on the rear part of the motor which is most easily accessed through the rear panel used for replacing the water pump. The water pump has three screws holding it and two hose clamps that come off easily with a pair of pliers. Before removing the water pump, I had to tip up the machine and take the belt off. This was also pretty easy. Put it back together and works great again on all cycles.

WASHER SHAKES AND DANCES

  • Customer: Adrian from West New York NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Wrench set
  • 10 of 12 people found this instruction helpful
NO NEED TO BUY A BRAKE WRENCH NOR THE EXPENSIVE SPRING REMOVER.
ONCE THE DRUM IS OUT THE WASHER TURN IT UPSIDE DOWN AND LOOSE THE SCREWS HOLDING THE TRANSMISSION ABOUT A LITTLE MORE THAN HALF WAY, TO GIVE THE NEW SNUBBER ENOUGH ROOM TO FIT IN, THEM TIGH AND ASSAMBLE EVERYTHING BACK TOGETHER

During the first rinse cycle, a loud metal to metal grinding sound occured. I shut down the machine and inspected thebottom of the washed and found the water pump hard to move. Obviously there was a problem.

  • Customer: Ed from Adamsville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 10 of 13 people found this instruction helpful
I simply emptied the machine of all the water, tilted the washer on its side,removed the small gray access panel located on the back of the washer, removed both hoses and the drive belt. Then I removed the three screw bolts that hold the water pump in place. Then I replaced the old pump with the new on by just following the process in reverse. I did notice that the new pump did not come with a metal support plate(at least thats what I called it. No problem though when I found out from a local repairman that its a newer design. Total time less than 15 minutes.

terrible grinding noise

  • Customer: ALVA K from chippewa falls WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 9 of 10 people found this instruction helpful
For safety I Unplugged the machine
Tipped machine back and removed the belt. Rotated the motor by hand and all is well there. Rotated the water pump by hand and a grinding sound appeared. I Let the machine down . Using a hard object , 1/16th of an inch thick, I slide it between the front edge of the lid and the front panel unlocking the clips ( one on the right side and one on the left side ) holding the lid down. I then tipped the lid up and removed the 2 screws holding the front panel on. Lifted the front panel off of the clips on the bottom end of panel. Using a nut driver I removed the 3 bolts holding the pump to the frame. Then with a pliers I removed the clips holding the 2 hoses. With a pan to catch the water I removed the hoses and drained them into the pan.
I then took my machine model number and went to the internet in search of a new water pump. After checking several sites with no success, I come upon the site for PartSelect.Com. With the excellent search method on the site I was able to quickly find the part I needed. I placed my order (10pm) on a Tuesday night and a short time later I received an email letting me know they had my order. On Wednesday I received an email letting me know they had shipped my order. On Friday the order had arrived.
I removed the new pump from the box and inspected it . Every thing looks great. I placed the pump into its mount on machine and bolted it down. Attached the 2 hoses, put the front panel back on and tipped the top down into place. Pushed machine into place, plugged it in and fired it up. I now have a quiet running machine again. Thank You to PartSelect.com for the quick response to my

the water would not stop filling machine.water over flowed on the floor.

  • Customer: Carolyn from Charlestown RI
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 11 of 16 people found this instruction helpful
found repairs on the internet. And my husband followed the repairs and the washer works wonderful thanks.

original Factory Water Pump Bearing seized up

  • Customer: Bill from Mount Pleasant MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 9 of 10 people found this instruction helpful
Vey Easy to Fix. 1)Turn Water off at the wall. 2)Remove access panel on back of washer. 3) Remove Water pump. It is bolted down to the bottom of the washer by three nut head bolts. when loose the pump can be manipulated and tilted so the belt will have slack and most likely fall right off. Have a bucket ready. Remove water hose from top of pump by sgueaing clam with pliars and sliding clamp up hose. allow to drain in bucket. Lift drain hose out from wall and allow to drain through the pump into bucket. remove hose from pump that goet to drain. Replace pump and reverse steps listed above.
All Instructions for the PAV2300AWW
61-75 of 517