This is a range temperature sensor, used to detect the interior temperature of your oven when it is baking or cooking. If you notice your oven is baking unevenly or at inconsistent temperatures, will ...
This is an oven burner igniter made for use with Samsung ovens. This oven burner igniter is designed to ignite the gas that flows into it, to produce heat. However, over time and with further frequent...
This surface burner cap is specially designed to fit with Samsung ranges. It is a genuine OEM replacement part supplied directly by Samsung to ensure compatibility. The burner cap is a round, black ca...
This oven cavity floor coating or bottom floor panel is an authentic OEM part supplied by Samsung to ensure compatibility with various models of Samsung ranges. It is a protective layer that sits on t...
The oven door switch shuts the oven light off when you close the oven door.
$67.34
In Stock
Questions And Answers for NX58F5500SS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Julius Lunn
December 6, 2019
The only oven control functions that still work are broil, light, and timer. The oven doesn't ignite for any of the other functions.I hear the touch panel beep, and see the display the settings i input, but the oven doesn't ignite.
For model number NX58F5500SS
Hello Julius, thank you for writing. You will want to replace the Oven Burner Igniter, part number PS4241428 for your model. Good luck with your repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Tom
December 10, 2019
It took 65 minutes to heat the oven to 425f
For model number NX58F5500SS
Hello Tom and thanks for writing.
The likely issue is a weak or failing oven igniter. Heat resistance igniters # PS4241428 can lose resistance as they get hot over time and won't send enough resistance to the gas valve to allow the main valve to come on. ... Most gas ovens should heat to 350-degrees in about 7-to-8 minutes. We hope this helps. Please contact us anytime.
The broil and some of the number buttons will not work on the display panel
For model number NX58F5500SS
Hi Kathy, thank you for reaching out. According to the symptom, the control board is defective and needs to be replaced to resolve the issue. The compatible control board for your model is part number PS8764724. If you require assistance to place an order, please contact customer service. We hope that helps!
The electrical doesn’t come on is there a reset switch on this model? The gas burners still work
For model number NX58F5500SS
Hi Jeffrey, thank you for your inquiry. Based on our research, there is no reset switch listed for your model. You can manually do so by unplugging it for a few minutes and then plugging it back on. If the issue persists, you may need to check the electronic control board, part number PS8764724, as it is most likely faulty and may need to be replaced. We hope this helps!
The Samsung stove I have has had the igniter replaced several times. It seems to wear out over a couple years time. I did the repair with a Philips #2 screw driver. Open the oven door, remove the grates. unscrew the bottom cover and expose the heat shield. Unscrew the heat shield. This exposes the burner. Unscrew the burner from the c
... Read moreenter of the plate/lower heat shield. Unscrew the burner from the front and back of the oven. Carefully lift up the burner to expose the igniter and clip. Unscrew the igniter from the burner and set the burner aside. Unclip the igniter from the power cable. If it falls below, it won't go far just reach in a lift it back up to fasten the new igniter to the power clip. Refasten to the burner with new clips and screws provided. Re-insert the burner to the gas jet that is below the bottom plate which will not be visible to you unless you place your head towards the rear of the stove and look down. Once the Jet is back into the hole of the burner, re fasten it to the middle back and front of the stove. Replace the covers and grates. Close the oven and test it. A new igniter does wonders. You can remove the stove door for a less intrusive install, but I found it unnecessary to do so and saved a step and time. I was done well under 30 minutes.
My barely 4 year old Samsung range/oven began not heating consistently. Even though it said 350, for example, we had to increase to 465 to get it to bake. Thought it was the temperature sensor. Ordered and installed new one easily. That didn't solve the problem. So, rather than throw more money at parts that may not have resolved the
... Read moreissue, I got a new Amana range. Samsung appliances go to my 'do not buy' list along with LG!