Models > NWXR483GG3WW

NWXR483GG3WW Hotpoint Dryer - Overview

Get Parts and Repair Help for NWXR483GG3WW

If you know the dryer repair part you need, you can browse the list of all parts on the NWXR483GG3WW, or you can search by name or part description. You can also find your part by where it is located on the NWXR483GG3WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for NWXR483GG3WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.78

Drum Bearing Slide

There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time. NOTE:Sold individually.

$6.40

Drum Bearing Slide - White

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

$18.13

Front Drum Bearing

Slides are NOT included. This part helps your dryer operate as quietly as possible. Note: The drum slides should also be replaced when your replacing the drum bearing.

$6.62

Lower Front Felt Drum Seal

May differ in appearance but functions same as original.

$3.62

D-Shaped Knob Insert Clip

Sold individually.

$19.98

Drive Belt

This drive belt is 89.5" long.

$3.79

Light Bulb - 120V 10W

$46.29

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible.

$31.61

Lint Filter and Frame

$2.50

HANDLE DOOR

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was squeeling when running.

  • Customer: Daniel from Chicago IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 388 of 390 people found this instruction helpful
I removed the two screws at the front above the drum opening (with the dryer door open). The top panel then lifts off. I removed the screw at each side that holds the front panel to the side panels, tilted the front panel forward, which disengages the front of the drum from the front drum glide bearing. I then lifted the front panel slightly, unhooking th... read more

Intermittant squeaking noise

  • Customer: Mark from Addison IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 402 of 475 people found this instruction helpful
Basically, I followed the same steps a prior person posted.
1.Removed the two screws inside the door, on the top part of the opening.
2.Lifted up and removed the top.
3.Removed two screws holding the front panel in place.
4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at the drum bearing wit... read more

Dryer made LOUD screaching constant sound

  • Customer: Brian from Langhorne PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 132 of 197 people found this instruction helpful
(1) open dryer door (2) remove screws holding door on and put door aside. Probably doesn't have to be done but I think its easier and safer so you don't accidently bend the hinges. (3) remove 2 screws holding top onto front. of dryer located in recess that door sits in (3) pull up on top and remove (from slots by the control panel) (4) remove final 2 screws ... read more