Models > NWXR473GV3WW

NWXR473GV3WW Hotpoint Dryer - Overview

Get Parts and Repair Help for NWXR473GV3WW

If you know the dryer repair part you need, you can browse the list of all parts on the NWXR473GV3WW, or you can search by name or part description. You can also find your part by where it is located on the NWXR473GV3WW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for NWXR473GV3WW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$6.92

Drum Bearing Slide - White

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

$18.13

Front Drum Bearing

Slides are NOT included. This part helps your dryer operate as quietly as possible. Note: The drum slides should also be replaced when your replacing the drum bearing.

$3.62

D-Shaped Knob Insert Clip

Sold individually.

$19.98

Drive Belt

This drive belt is 89.5" long.

$46.29

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running...

$3.21

HANDLE DOOR

$14.88

Idler Pulley Wheel

A dryer's idler pulley wheel serves to help the belt to rotate the drum.

$26.67

Rotary Start Switch

This part is used to start the dryer once you have selected a setting on the timer.

$87.59

Front Air Duct Assembly

With this front air duct assembly it includes the lower drum seal, duct seal and the moisture sensor bars. The air duct assembly is located on the backside of the front panel and i...

$2.79

LATCH DOOR

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

original duct was broken

  • Customer: Chad from Gilbert SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 85 of 91 people found this instruction helpful
Dear PartSelect.com,

My repair went off without a hitch.

2 screws removed to remove top.
4 screws removed from inside to remove front panel w/ door.
4 screws removed from top of control panel, loosed and popped top right off.
Flathead screwdriver to pop off old plastic panel.
Removed old wire chase (plastic, approx 3... read more

Drum belt broke

  • Customer: Adrian from Middletown MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 80 of 103 people found this instruction helpful
Removed the front Dryer panel. Left drum in place and lifted it up slightly to get access to motor drive. Slipped belt in place and put panel back on.
This was a first attempt ever at fixing an appliance and it was no big deal. read more

Broken Knob Post

  • Customer: Jaren from Lemoore CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 68 of 82 people found this instruction helpful
First I unplugged the dryer, then I removed the access panel on the back of the control panel. I removed the wires from the back of the switch...Here is where I messed up. I removed the switch prior to ordering the part, the bad part is the way I removed the part. When you get the new part in you will be able to see how it will be mounted to the control pane... read more