Quick Question!

Have you ever purchased from PartSelect.com before?

Models > NWXR473GV2AA

NWXR473GV2AA Hotpoint Dryer - Overview

Get Parts and Repair Help for NWXR473GV2AA

If you know the dryer repair part you need, you can browse the list of all parts on the NWXR473GV2AA, or you can search by name or part description. You can also find your part by where it is located on the NWXR473GV2AA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for NWXR473GV2AA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.02

Drum Bearing Slide - Green

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

Order within the next 2 mins and your part ships today!
$8.97

Drum Bearing Slide - White

Sold individually. There are 2 per dryer. They attach to the outer-most sides of the bearing. Manufacture recommends to replace both slides at the same time.

Order within the next 2 mins and your part ships today!
$44.28

Front Drum Bearing

Note: The drum slides should also be replaced when your replacing the drum bearing. Slides are NOT included. This part helps your dryer operate as quietly as possible.

Order within the next 2 mins and your part ships today!
$8.55

Duct Felt Seal

May differ in appearance but functions same as original.

Order within the next 2 mins and your part ships today!
$8.21

D-Shaped Knob Insert Clip

Sold individually.

Order within the next 2 mins and your part ships today!
$22.48

Drive Belt

This drive belt is 89.5" long.

Order within the next 2 mins and your part ships today!
$49.31

Rear Drum Bearing Kit

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running...

Order within the next 2 mins and your part ships today!
$3.59

LAMP

Sold individually.

Order within the next 2 mins and your part ships today!
$38.01

Cycling Thermostat - 4 Wire

This thermostat helps to regulate the dryer's internal temperature. L210-30F

Order within the next 2 mins and your part ships today!
$12.23

Interlock Switch

This part is a simple on/off mechanism that prohibits the appliance from operating when the door is open.

Order within the next 2 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic

  • Customer: Matthew from Plainfield, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 646 of 722 people found this instruction helpful
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the ne... read more

Dryer was squeeling when running.

  • Customer: Daniel from Chicago, IL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 580 of 655 people found this instruction helpful
I removed the two screws at the front above the drum opening (with the dryer door open). The top panel then lifts off. I removed the screw at each side that holds the front panel to the side panels, tilted the front panel forward, which disengages the front of the drum from the front drum glide bearing. I then lifted the front panel slightly, unhooking th... read more

Intermittant squeaking noise

  • Customer: Mark from Addison, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 531 of 659 people found this instruction helpful
Basically, I followed the same steps a prior person posted.
1.Removed the two screws inside the door, on the top part of the opening.
2.Lifted up and removed the top.
3.Removed two screws holding the front panel in place.
4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at the drum bearing wit... read more