Models > NVL333GY0WW > Instructions

NVL333GY0WW Hotpoint Dryer - Instructions

All installation instructions for NVL333GY0WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the NVL333GY0WW
46-53 of 53
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken post on switch

  • Customer: Myron from Blairsville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed 4 scewws deom case snapped out switch placed the new one attached two wires re attached with the 4 screws

making noise, eating cloths

  • Customer: dale from Sedro Woolley WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off dryer breaker!!Pryed dryer top up and off using flat blade screwdriver, removed two philips head screws inside and top, rermoved wires for door switch. I pulled off the old drum slide and lower felt. I scraped the large left overs and used some solvent to clean the remaining fuzz. I glued the felt and slide per the instructions, applied the new parts. I waited about 30 minutes and assembled, it did make a squeaking noise for about 2 minutes. When everything seated in the noise was gone. $150.00 and simple mechanics saved me from spending more on a new dryer, mine is 15 yrs old.

Stackable washer & dryer

  • Customer: Spencer from Chicago IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Scared to do the work myself found this website which gave me basic instructions and access to parts needed. Ordered and made an error called and CS took care of me right away. Fast friendly and will buy from them again. Great service great parts and great people!

INOPERATIVE SWITCH

  • Customer: KENDALL from COCOA FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
REMOVE & RPLACE SWITCH

Drum would not turn at full speed, noisy squeak

  • Customer: Linda from Edna TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Top control panel removed; next used screwdriver to lift up dryer top on each side( the top of dryer is attached by clips on the underside) the dryer front panel has two screws, one on each side of inside front(they are easy to reach and near the top of the inside front panel, after removing these two screws we used screwdriver again to pry off front panel as it is attached also by clips on inside of front panel. At this point there is easy access to the drum where the old belt was removed, new belt put in place; removed small panel on back of dryer to access idler pulley and attached new belt through the pulley; turned the drum a couple of times by hand to check if belt was running true on the drum; problem fixed.

Start switch broke

  • Customer: Sherry from Marietta OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Followed the on line instructions.

No heat

  • Customer: jeff from perrysburg OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The wife complained of clothes not drying. Ordered a igniter without checking for exact cause to save time. When I was able to I took the top and front panels off. Unfortunately the igniter was fine. I ruled out the limits and igniter with a VOM meter. I quickly ordered the gas valve solenoids. After a quick delivery they were replaced with a screw driver and panels replaced. Works fine.

Loud squeal when dryer in operation

  • Customer: Tracy from Washington DC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
This was done to a washer/dryer that is in a closet and was worked on in place and not removed so it was all done through the front. Its a good idea to vacuum the inside out before putting it all back together. 1.Remove all of the screws that hold down the top of the dryer and remove top. 2. Remove the front slanted panel below the controls then Remove the two small black screws holding the plastic inserts on the left and right sides of the controls panel plus the two silver screws that will allow it to drop so that you can access the tabs that hold the front section on. 3. Remove screws holding the front section with the door on. The last two will be tabs at bottom that were hidden by control panel. Unplug connector and remove front. 4. Note how belt is positioned around motor and tensioner before removing belt.(just push tensioner until belt is loose enough to slide off of drum to remove belt). 5.Slide out drum and remove old bearing and replace with new one. Be especially careful tightening the three screws that attach the bearing as they are easy to strip. 6. To remove the bushing at the back of the dryer you will remove the two screws. but you will need to hold the clip on the back of the dryer or it will drop when the screws are removed. When re-installing MAKE SURE not to lose your ball bearing that the drum bearing will rest against. I used a strong small magnet to hold the ball bearing against the back of the nylon cradle bushing so I wouldn't lose it when re-installing the bushing and it worked great. Once the nylon bushing was back in place I lubed it thoroughly and put everything back in reverse order. I usually would not fill out one of these do-it-yourself forms but the instructions that are already listed with this part are completely different from what I encountered up to the actual bearing and bushing replacement. Hope this helps.
All Instructions for the NVL333GY0WW
46-53 of 53