Models > NVL333EY0WW > Instructions

NVL333EY0WW Hotpoint Dryer - Instructions

All installation instructions for NVL333EY0WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the NVL333EY0WW
31-42 of 42
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer sounded like a stuck pig

  • Customer: Christopher from Palm Beach Gardens FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 9 people found this instruction helpful
I ordered the rear bearing kit from the local supplier here in Marsh Harbour, Abaco the Bahamas. Delivery for the kit was 3 to 4 weeks from my local supplier.NOT PARTSELECT.
While waiting I found this site and after reading the VERY helpful instructions from your customers, I realised that I would probably need additional parts, top and bottom front felt seals, maybe a new drive belt.
I ordered these online and had the parts deliverd to a friends address in West Palm Beach Florida. The parts arrived in about 2 days. My wife was already there and brought the parts back.

Installation was very straight forward. Read the other installation reports and you will not have a problem.
The only thing I can add is, DO NOT LOOSE THE SMALL BALL BEARING. I did and it took me about an hour to find it.
My suggestion is to do a dry run installation of the bracket WITH OUT the small ball bearing. Tape the backing plate?that keeps the ball breaing inplace to the outside of the back panel with duct tape so that the screw hole will line up. Once this is done put some grease (Supplied with the kit) in the hole on the nylon bracket and attach with the two screws, do not over tighten. Grease up the area where the rear bearing shaft support will sit.

Installation of the rear bearing shaft support was straight forward. This is on the dryer drum. Extra hands are must for this.

I was very pleased with Partselct.
Dryer works like new.

The switch was broken and had to use pliers to start dryer

  • Customer: Dan from Fernley NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnected the power removed 4 screws from top panel. Removed 2 wires, turned switch counter clockwise. remopved switch. Replaced with new switch,connected the 2 wires, put panel back inplace,put screws back in panel,plugged dryer back in. SUPER SIMPLE Total time 5 minutes

Sticker Switch Worn Out

  • Customer: Roy from Sun City West AZ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simple replaced switch

Lack of grease caused bearing to go out

  • Customer: GARY from HALEYVILLE AL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I took the top and front off the dryer. I then took the screws out of the drum and removed the drum. I then took the old bearing out and put the new one in.

Something fell off a shelf and broke the switch off

  • Customer: Randall from mcloud OK
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the start switch.

switha broke off

  • Customer: Sue from Norfolk MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed old switch, replaced it with new

Dryer start switch broken off

  • Customer: David from Ennis MT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Put in the new switch and it starts great. Now that it runs there is no heat. I assume the elements are out.

broken post on switch

  • Customer: Myron from Blairsville GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed 4 scewws deom case snapped out switch placed the new one attached two wires re attached with the 4 screws

making noise, eating cloths

  • Customer: dale from Sedro Woolley WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off dryer breaker!!Pryed dryer top up and off using flat blade screwdriver, removed two philips head screws inside and top, rermoved wires for door switch. I pulled off the old drum slide and lower felt. I scraped the large left overs and used some solvent to clean the remaining fuzz. I glued the felt and slide per the instructions, applied the new parts. I waited about 30 minutes and assembled, it did make a squeaking noise for about 2 minutes. When everything seated in the noise was gone. $150.00 and simple mechanics saved me from spending more on a new dryer, mine is 15 yrs old.

INOPERATIVE SWITCH

  • Customer: KENDALL from COCOA FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
REMOVE & RPLACE SWITCH

Drum would not turn at full speed, noisy squeak

  • Customer: Linda from Edna TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Top control panel removed; next used screwdriver to lift up dryer top on each side( the top of dryer is attached by clips on the underside) the dryer front panel has two screws, one on each side of inside front(they are easy to reach and near the top of the inside front panel, after removing these two screws we used screwdriver again to pry off front panel as it is attached also by clips on inside of front panel. At this point there is easy access to the drum where the old belt was removed, new belt put in place; removed small panel on back of dryer to access idler pulley and attached new belt through the pulley; turned the drum a couple of times by hand to check if belt was running true on the drum; problem fixed.

Start switch broke

  • Customer: Sherry from Marietta OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Followed the on line instructions.
All Instructions for the NVL333EY0WW
31-42 of 42