Quick Question!

Have you ever purchased from PartSelect.com before?

Models > NTW5500TQ1

NTW5500TQ1 Amana Washer - Overview

Get Parts and Repair Help for NTW5500TQ1

If you know the washer repair part you need, you can browse the list of all parts on the NTW5500TQ1, or you can search by name or part description. You can also find your part by where it is located on the NTW5500TQ1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for NTW5500TQ1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$11.77

Direct Drive Motor Coupling

The direct drive motor coupling, also known as a coupling kit, is a newer version of the part and is used in your washer. The piece includes new metal sleeves that have been added ...

$45.80

Clutch Assembly

A clutch assembly is found in your washing machine and is responsible for spinning the basket during the spin cycle. A worn-down clutch can lead to a slower spin which can lead to the machine not draining properly, leaving your clothes wet after a cycle. If you notice a burning smell, or the machine shaking and moving more than normal, this could indicate the need to replace your clutch. This clutch assembly comes with a brake cam driver, blue springs for large capacity washers, and a black spring for compact washers. As per the factory, the green spring (1.24 inches) replaces the black spring (1.46 inches). This repair requires a half inch 1/16th socket with an extension and a ratchet, a pair of channel lock pliers, a Phillips screwdriver, medium size flat blade, a small flat blade, and a 1/4 inch nut driver.

$2.92

Suspension Spring

The suspension is meant to support the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down, or perhaps has stretched ou...

$23.02

Switch, Lid

This part is found in your washer. The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the green grounding wire. If your machine is having trouble starting, is not agitating, spinning, or is not draining properly, this could be because the lid switch has broken. You will need a 5/16-inch nut driver for this repair. The package will contain one lid switch. You will need to access the back of the washer, and remove the two Phillips screws that hold the top back panel in place. Slide the panel forward to release. Use your nut driver to loosen the screw that holds the ground wire in place. Lift the lid of the washer to release the old lid switch.

$3.56

Tub Spring

This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of th...

$4.63

Screw & Washer (5/16-24 x 1)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$15.56

Agitator Cam Kit

This kit included the cam, 4 dogs and bearing.

$4.48

Seal, Inner Cap

Also known as an O-Ring. This black o-ring seal is three inches in diameter.

$12.21

Tub Wear Pads - Package of 3

This package of pads contains three brown tub wear pads.

$4.48

Agitator Cap Barrier with Seal

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No movement from Basket & agitator

  • Customer: Jeff from Wayne, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 889 of 943 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more

spin cycle did not engage

  • Customer: Andrew from SLC, UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 369 of 393 people found this instruction helpful
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase... read more

Washer wouldn't run

  • Customer: Clint from Kansas City, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 248 of 272 people found this instruction helpful
I removed the two screws on the back of the control panel. The control panel then flips back. The switch is on the left side. To remove the switch, I first detached the wire to the control panel and unscrewed the grounding wire. The new switch drops right in. I had a little trouble getting it in until I realized the washer lid had to be open. A little ... read more