Models > NT15H41 (9B01A)

NT15H41 (9B01A) Admiral Refrigerator - Overview

Get Parts and Repair Help for NT15H41

If you know the refrigerator repair part you need, you can browse the list of all parts on the NT15H41, or you can search by name or part description. You can also find your part by where it is located on the NT15H41 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for NT15H41 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the NT15H41 [Viewing 2 of 2]

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.70

Screw

This screw is sold individually.

$31.14

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air cooling for the condenser coil.

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$2.70

SCREW

Sold individually.

$28.61

BLADE-FAN

$59.62

Evaporator Fan Motor - Blade NOT Included

This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils.

$38.56

6-Hour Defrost Timer

This part may appear different than the original, but will function the same. This device acts like a clock. It continually advances and alternates between activating the cooling...

$2.70

Speed Nut

$23.96

Defrost Thermostat - With Wire and Clip

This refrigerator defrost thermostat will cut out at 80 degrees Fahrenheit and kick back when the temperature drops to 15 degrees Fahrenheit.

$17.75

Ice Cube Tray

This tray makes 48 mini ice cubes.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 77 of 80 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

cocktails running out of ice

  • Customer: Craig from Westminster CA
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 49 of 54 people found this instruction helpful
filled both ice cube trays up with water and placed in the freezer.. within hours my ice oproduction was doubled! no more warm cocktails : ) read more

noisy fan motor

  • Customer: robert from nashotah WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 16 of 19 people found this instruction helpful
rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, close up, reverse pan... read more