Quick Question!

Have you ever purchased from PartSelect.com before?

Models > NGD7200TW10

NGD7200TW10 Amana Dryer - Overview

Get Parts and Repair Help for NGD7200TW10

If you know the dryer repair part you need, you can browse the list of all parts on the NGD7200TW10, or you can search by name or part description. You can also find your part by where it is located on the NGD7200TW10 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for NGD7200TW10 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$27.70

Radiant Flame Sensor

If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor...

$31.93

Thermistor

This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.

$6.12

Touch-Up Paint - White

This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, ...

$31.62

Drum Support Roller with Axle

Sold individually.

$22.71

Thermostat

This thermostat helps to regulate the dryer's internal temperature.

$41.05

Gas Dryer Conversion Kit - NG to LP

This conversion kit contains all parts needed to convert your gas dryer from natural gas (NG) to liquid propane (LP). This kit will work with some Samsung dryers as well. Use model # to ensure you are getting the correct part.

$56.45

Lint Filter

This filter collects lint as it passes through the dryer vent.

$41.87

High Limit Thermostat

This hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. With this thermostat, a dryer's heating element will cut out if the internal temperature reaches 260 degrees Fahrenheit. The element will kick back in when the temperature drops to 210 degrees Fahrenheit - the differential of 50 degrees.

$59.31

Drive Belt

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

$11.54

Spray Paint - 12 oz. - White

Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a protective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Gas Flame Would Drop Out

  • Customer: FRED from BRIELLE, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 45 of 62 people found this instruction helpful
First it was a process of alimination to find out why it was dropping out. After the problem was found it was just a matter of replacing the holding coil on the gas valve. Thank you fred kenney sr read more

A faulty computer

  • Customer: keri from lincoln park, NJ
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 34 of 40 people found this instruction helpful
First remove the top of this particular dryer, to get to the necessary screws. computer is located on the left side, and 3 screws frees it up. Then disconnect the wires. Unscrew the board, and replace!! That simple!! Unfortunately for me the bad computer melted part of the wire harness. I called maytag and drove them nuts untill they paid to replace th... read more

Dryer did not turn when power was on.

  • Customer: JAMIE from VALLEY STREAM, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 27 of 34 people found this instruction helpful
Callled the service company to diagnose the problem. Watched him take machine apart. He found the problem. Told me the parts that I needed. Didnt know what they were. Went to partselect.com looked my model up and found parts and ordered. Followed same steps as repair guy: Two screws in back of machine then slide top off. Six screws in front to remove fron... read more